Donate!
Welcome, Guest. Please Login or Register :: View Members
Pages: 1 2 3 
Send Topic Print
Off beat measurments and sizes (Read 2479 times)
steelwolf
Serious Thumper
*****
Offline

"I'm a cowboy,
on a steel horse I
ride."

Posts: 847
Trinity, NC
Gender: male
Off beat measurments and sizes
12/22/06 at 08:15:53
 
First off please let me ask that this list not be hijacked into a discussion. Comments can be directed to members via private message and they can in turn, modify their posts here if necessary.
I guess I'll go first. I browsed the site for a few of these so thanks to the ones who posted them.

Handlebars...1"

Exhaust header @ muffler end...1.75"OD

Piston diameter...94mm

Fuel line...5/16"

Vaccume line...3/16"

Fork diameter...38mm

Oil drain plug (determined by year)...14mm or 17mm

Overall length...86.2"

Overall width...30.5"

please continue......
Back to top
 
 

WWW   IP Logged
Serowbot
YaBB Moderator
ModSquad
*****
Offline

OK.... so what's the
speed of dark?

Posts: 28910
Tucson Az
Gender: male
Re: Off beat measurments and sizes
Reply #1 - 12/30/06 at 10:23:12
 

Front sprocket....  32mm socket

Rear axle....          17mm Rtside / 24mm Ltside
Back to top
 
 

Ludicrous Speed !... ... Huh...
  IP Logged
thumperclone
Serious Thumper
Alliance Member
*****
Offline

PGR rider  riding
with respect

Posts: 6301
Grand Junction Colorado
Gender: male
Re: Off beat measurments and sizes
Reply #2 - 12/31/06 at 09:34:49
 
idle speed 1k-1.2k rpm
plug gap  0.8-0.9mm (ngk  dpr7ea-9)
comp ratio 8.5-1
dry weight 352#,355# calif model
displacement 39.8 cu.in.
got more if needed some are year specific..
Back to top
 
 

standing for those who stood for US
















  IP Logged
steelwolf
Serious Thumper
*****
Offline

"I'm a cowboy,
on a steel horse I
ride."

Posts: 847
Trinity, NC
Gender: male
Re: Off beat measurments and sizes
Reply #3 - 12/31/06 at 10:57:37
 
Screw sizes....

Carburator Bowl - M5
Floatchamber - M5
The little cover on the RH side of the carb is the
Transient Enrichment Valve - M4




Thanks Kropatchek
Back to top
 
 

WWW   IP Logged
steelwolf
Serious Thumper
*****
Offline

"I'm a cowboy,
on a steel horse I
ride."

Posts: 847
Trinity, NC
Gender: male
Re: Off beat measurments and sizes
Reply #4 - 01/18/07 at 18:21:24
 
Muffler adapter bend is 10 degrees

White spacer thickness = approx. 2.8mm or .111"
Back to top
 
 

WWW   IP Logged
franch
Senior Member
****
Offline

I love YaBB 1G -
SP1!

Posts: 287

Fork cap nut size
Reply #5 - 04/30/07 at 02:43:33
 
fork cap nuts = 27mm

lower fork tube allen bolts = 8mm you need a fairly long one maybe 3-4 inches
Back to top
 
 
  IP Logged
verslagen1
YaBB Moderator
ModSquad
*****
Offline

Where there's a
will, I want to be
in it.

Posts: 28923
L.A. California
Gender: male
Re: Off beat measurments and sizes
Reply #6 - 08/17/07 at 15:14:18
 
rigidchop wrote on 12/31/69 at 16:00:08:
for future reference on an 87, it's 30 mm for the crank and 32 mm for the clutch. thanks for your help.
Back to top
 
 
WWW   IP Logged
drums1
Serious Thumper
*****
Offline

'87 Savage
Bashed--Down for the
count

Posts: 664
Racine, Wisconsin
Gender: male
Re: Off beat measurments and sizes
Reply #7 - 06/06/10 at 14:09:48
 
Anyone know the carb float settings? (height and drop?)

Fuel level 0.256 to 0.296"
Float ht. 1.06 to 1.114 "
Back to top
 
« Last Edit: 11/22/10 at 19:55:16 by verslagen1 »  
  IP Logged
youzguyz
Serious Thumper
*****
Offline



Posts: 2547
San Antonio, Texas
Gender: male
Re: Off beat measurments and sizes
Reply #8 - 08/08/13 at 08:54:55
 
Oil Filter O-ring
Copy/Paste from post by HondaLavis before it gets lost in the general mish-mash of the universe
=========================================
Did some looking to compare the dimensions of the stock o-ring to the assortment they had at O'Reilly's.  The stock dimensions are 2.4mm thickness, 15.8mm inner diameter.  The assorted individual o-rings were all SAE.  The closest was 3/32 thickness, 5/8 inner diameter.  Translate that to metric, that's a 2.3813mm thickness, and 15.8750mm inner diameter.  I can't imagine a couple of hundredths of a MILLIMETER making a huge difference.

For anyone else who needs this O-ring, it should be #114 at O'Reilly's.  All  said and done, I spent $0.65.  And, YES, it will be fine in the oil.   Wink

::UPDATE::

I just put it on, and it fits just fine.  Nice and tight around the fitting to the filter, and it provides positive pressure when you push the filter against it.  Again, to any of you with PO's who lost an o-ring (because none of US have ever lost them, right?  Roll Eyes )  here is the $0.65 answer.
Back to top      
Back to top
 
 

2002 - Silver (Thumper)
2000 - Green (Mad Hamish)
Most motorcycle problems are caused by the nut between the seat and the handlebars. Make sure yours isn't too tight or too loose.
  IP Logged
danjray
Junior Member
**
Offline



Posts: 83
Connecticut
Gender: male
Re: Off beat measurments and sizes
Reply #9 - 08/12/13 at 06:02:14
 
The 2 screws holding the slide needle down inside the slide are M3 *~6mm length.
Back to top
 
« Last Edit: 04/28/15 at 04:37:52 by Dave »  

2012 LS650 Boulevard S40
~11k Miles and counting fast
Mech Engr Student and backyard tinkerer
  IP Logged
verslagen1
YaBB Moderator
ModSquad
*****
Offline

Where there's a
will, I want to be
in it.

Posts: 28923
L.A. California
Gender: male
Re: Off beat measurments and sizes
Reply #10 - 01/12/14 at 20:38:19
 
Valve cover O-rings are -139, fits tight to the outside.
-138 might fit too, but the -139 are self retaining and what I had access too.
Back to top
 
 
WWW   IP Logged
MnSpring
Serious Thumper
*****
Offline

Younger than most
people my age.

Posts: 9567
Minn
Gender: male
Re: Off beat measurments and sizes
Reply #11 - 01/06/15 at 17:28:12
 
32  MM   =  1-1/4 SAE
Back to top
 
 

Ben Franklin once said: "If you give up a freedom, for the sake of security, you will have neither".
Which is More TRUE, today, than yesterday.('06, S-40, Stock) well, mostly .
  IP Logged
Kenny G
Serious Thumper
*****
Offline

SuzukiSavage.com The
Singles Club...LOL

Posts: 1754
Robson Ranch, Denton, Texas
Gender: male
Re: Off beat measurments and sizes
Reply #12 - 01/22/15 at 13:02:43
 
Suzuki Factory Risers

Both the Allen bolts in the top of the risers, and the studs coming out of the bottom of the risers are:

10 MM x 1.25 threads    This is a finer thread than the common pitch which is 1.5 threads

Kenny G

Todd James wrote on 06/23/15 at 20:56:13:
On my 2007 S40 the risers are 100 mm apart center to center.
Back to top
 
« Last Edit: 06/23/15 at 21:03:08 by verslagen1 »  
  IP Logged
Dave
YaBB Moderator
ModSquad
*****
Offline

SuzukiSavage.com
Rocks!

Posts: 18160
Camp Springs, Kentucky
Gender: male
Re: Off beat measurments and sizes
Reply #13 - 01/28/15 at 05:00:19
 
The thread size and pitch for the carb idle fuel mixture is a 6.0mm x 0.50.  This is a very fine pitch....taps are available in this size, and you may need to use one if the carb body is corroded and the screw is too tight.  The screw should move in/out easily.
Back to top
 
 

Someday I will be old......But not today!

  IP Logged
Jeff71
Senior Member
****
Offline

I'm a bike noob!!!!!

Posts: 378
South of Chicago, the suburbs
Gender: male
Re: Off beat measurments and sizes
Reply #14 - 04/11/15 at 12:24:25
 
I raided ACE today and found the cap to cover the speedo cable hole on the engine. The threads on the engine are actually 16mm-1.5pitch but this cap went on fine.

A little RTV around the base and things should be sealed right up.
Jeff
Back to top
 
 

Yeah, like I have any clue what is going on....
http://myrycabuild.weebly.com
  IP Logged
Pages: 1 2 3 
Send Topic Print


« Home

 
« Home
SuzukiSavage.com
12/08/24 at 00:24:08



General CategoryTechnical Documents/Reference › Off beat measurments and sizes


SuzukiSavage.com » Powered by YaBB 2.2!
YaBB © 2000-2007. All Rights Reserved.