SuzukiSavage.com - Off beat measurments and sizes

steelwolf

Serious Thumper

Offline

"I'm a cowboy,
on a steel horse I
ride."

Posts: 847
Trinity, NC
Gender: male

Off beat measurments and sizes
12/22/06 at 08:15:53

First off please let me ask that this list not be hijacked into a discussion. Comments can be directed to members via private message and they can in turn, modify their posts here if necessary.
I guess I'll go first. I browsed the site for a few of these so thanks to the ones who posted them.

Handlebars...1"

Exhaust header @ muffler end...1.75"OD

Piston diameter...94mm

Fuel line...5/16"

Vaccume line...3/16"

Fork diameter...38mm

Oil drain plug (determined by year)...14mm or 17mm

Overall length...86.2"

Overall width...30.5"

please continue......

Back to top

IP Logged

Serowbot YaBB Moderator ModSquad Offline OK.... so what's the speed of dark? Posts: 28910 Tucson Az Gender:	Re: Off beat measurments and sizes Reply #1 - 12/30/06 at 10:23:12 Front sprocket.... 32mm socket Rear axle.... 17mm Rtside / 24mm Ltside
Back to top	Ludicrous Speed !... ... ... IP Logged

thumperclone Serious Thumper Alliance Member Offline PGR rider riding with respect Posts: 6301 Grand Junction Colorado Gender:	Re: Off beat measurments and sizes Reply #2 - 12/31/06 at 09:34:49 idle speed 1k-1.2k rpm plug gap 0.8-0.9mm (ngk dpr7ea-9) comp ratio 8.5-1 dry weight 352#,355# calif model displacement 39.8 cu.in. got more if needed some are year specific..
Back to top	standing for those who stood for US IP Logged

steelwolf Serious Thumper Offline "I'm a cowboy, on a steel horse I ride." Posts: 847 Trinity, NC Gender:	Re: Off beat measurments and sizes Reply #3 - 12/31/06 at 10:57:37 Screw sizes.... Carburator Bowl - M5 Floatchamber - M5 The little cover on the RH side of the carb is the Transient Enrichment Valve - M4 Thanks Kropatchek
Back to top	IP Logged

steelwolf Serious Thumper Offline "I'm a cowboy, on a steel horse I ride." Posts: 847 Trinity, NC Gender:	Re: Off beat measurments and sizes Reply #4 - 01/18/07 at 18:21:24 Muffler adapter bend is 10 degrees White spacer thickness = approx. 2.8mm or .111"
Back to top	IP Logged

franch Senior Member Offline I love YaBB 1G - SP1! Posts: 287	Fork cap nut size Reply #5 - 04/30/07 at 02:43:33 fork cap nuts = 27mm lower fork tube allen bolts = 8mm you need a fairly long one maybe 3-4 inches
Back to top	IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28923 L.A. California Gender:	Re: Off beat measurments and sizes Reply #6 - 08/17/07 at 15:14:18 rigidchop wrote on 12/31/69 at 16:00:08: for future reference on an 87, it's 30 mm for the crank and 32 mm for the clutch. thanks for your help.
Back to top	Versey's Place Tech Section Index IP Logged

drums1 Serious Thumper Offline '87 Savage Bashed--Down for the count Posts: 664 Racine, Wisconsin Gender:	Re: Off beat measurments and sizes Reply #7 - 06/06/10 at 14:09:48 Anyone know the carb float settings? (height and drop?) Fuel level 0.256 to 0.296" Float ht. 1.06 to 1.114 "
Back to top	« Last Edit: 11/22/10 at 19:55:16 by verslagen1 » IP Logged

youzguyz

Serious Thumper

Offline

Posts: 2547
San Antonio, Texas
Gender: male

Re: Off beat measurments and sizes
Reply #8 - 08/08/13 at 08:54:55

Oil Filter O-ring
Copy/Paste from post by HondaLavis before it gets lost in the general mish-mash of the universe
=========================================
Did some looking to compare the dimensions of the stock o-ring to the assortment they had at O'Reilly's. The stock dimensions are 2.4mm thickness, 15.8mm inner diameter. The assorted individual o-rings were all SAE. The closest was 3/32 thickness, 5/8 inner diameter. Translate that to metric, that's a 2.3813mm thickness, and 15.8750mm inner diameter. I can't imagine a couple of hundredths of a MILLIMETER making a huge difference.

For anyone else who needs this O-ring, it should be #114 at O'Reilly's. All said and done, I spent $0.65. And, YES, it will be fine in the oil. Wink

::UPDATE::

I just put it on, and it fits just fine. Nice and tight around the fitting to the filter, and it provides positive pressure when you push the filter against it. Again, to any of you with PO's who lost an o-ring (because none of US have ever lost them, right? Roll Eyes ) here is the $0.65 answer.
Back to top

Back to top

2002 - Silver (Thumper)
2000 - Green (Mad Hamish)
Most motorcycle problems are caused by the nut between the seat and the handlebars. Make sure yours isn't too tight or too loose.

IP Logged

danjray Junior Member Offline Posts: 83 Connecticut Gender:	Re: Off beat measurments and sizes Reply #9 - 08/12/13 at 06:02:14 The 2 screws holding the slide needle down inside the slide are M3 *~6mm length.
Back to top	« Last Edit: 04/28/15 at 04:37:52 by Dave » 2012 LS650 Boulevard S40 ~11k Miles and counting fast Mech Engr Student and backyard tinkerer IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28923 L.A. California Gender:	Re: Off beat measurments and sizes Reply #10 - 01/12/14 at 20:38:19 Valve cover O-rings are -139, fits tight to the outside. -138 might fit too, but the -139 are self retaining and what I had access too.
Back to top	Versey's Place Tech Section Index IP Logged

MnSpring Serious Thumper Offline Younger than most people my age. Posts: 9567 Minn Gender:	Re: Off beat measurments and sizes Reply #11 - 01/06/15 at 17:28:12 32 MM = 1-1/4 SAE
Back to top	Ben Franklin once said: "If you give up a freedom, for the sake of security, you will have neither". Which is *More TRUE, today, than yesterday.('06, S-40, Stock) well, mostly* . IP Logged

Kenny G

Serious Thumper

Offline

SuzukiSavage.com The
Singles Club...LOL

Posts: 1754
Robson Ranch, Denton, Texas
Gender: male

Re: Off beat measurments and sizes
Reply #12 - 01/22/15 at 13:02:43

Suzuki Factory Risers

Both the Allen bolts in the top of the risers, and the studs coming out of the bottom of the risers are:

10 MM x 1.25 threads This is a finer thread than the common pitch which is 1.5 threads

Kenny G

Todd James wrote on 06/23/15 at 20:56:13:

On my 2007 S40 the risers are 100 mm apart center to center.

Back to top

« Last Edit: 06/23/15 at 21:03:08 by verslagen1 »

IP Logged

Dave YaBB Moderator ModSquad Offline SuzukiSavage.com Rocks! Posts: 18160 Camp Springs, Kentucky Gender:	Re: Off beat measurments and sizes Reply #13 - 01/28/15 at 05:00:19 The thread size and pitch for the carb idle fuel mixture is a 6.0mm x 0.50. This is a very fine pitch....taps are available in this size, and you may need to use one if the carb body is corroded and the screw is too tight. The screw should move in/out easily.
Back to top	Someday I will be old......But not today! IP Logged

Jeff71 Senior Member Offline I'm a bike noob!!!!! Posts: 378 South of Chicago, the suburbs Gender:	Re: Off beat measurments and sizes Reply #14 - 04/11/15 at 12:24:25 I raided ACE today and found the cap to cover the speedo cable hole on the engine. The threads on the engine are actually 16mm-1.5pitch but this cap went on fine. A little RTV around the base and things should be sealed right up. Jeff
Back to top	Yeah, like I have any clue what is going on.... http://myrycabuild.weebly.com IP Logged