Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› Having trouble loosening fork legs from crown
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages:
1
2
3
Having trouble loosening fork legs from crown (Read 235 times)
ohiomoto
Serious Thumper
Offline
SuzukiSavage.com
Rocks!
Posts: 2690
WTF is JOG?
Re: Having trouble loosening fork legs from crown
Reply #15 -
07/17/19 at 06:42:30
I could be wrong, but I THINK if you remove the lower bushing from the upper, you can remove the seals from the bottom.
Back to top
IP Logged
oldNslow
Serious Thumper
Offline
SuzukiSavage.com
Rocks!
Posts: 2679
Rochester, NY
Gender:
Re: Having trouble loosening fork legs from crown
Reply #16 -
07/17/19 at 08:24:55
ohiomoto wrote
on 07/17/19 at 06:42:30:
I could be wrong, but I THINK if you remove the lower bushing from the upper, you can remove the seals from the bottom.
http://i178.photobucket.com/albums/w264/punkskalar/LS650%20Savage%20Forks/100...
But with the lower bushing on the tube and the upper bushing and the seal installed in the lower, I don't think you can then slide the lower back on to the tube. I've never done a set of Savage seals though, but I've done others and they have all required the tube to be
in
the lower before the seal and upper bushing were installed. The upper bush and the seal have to be slid down the tube from the top, which means the tube has to be removed from the triple trees.
If that's not the case then our forks are different from any that I've ever seen and I've just learned something that I didn't know.
Back to top
IP Logged
verslagen1
YaBB Moderator
ModSquad
Offline
Where there's a
will, I want to be
in it.
Posts: 28769
L.A. California
Gender:
Re: Having trouble loosening fork legs from crown
Reply #17 -
07/17/19 at 08:29:13
oldNslow wrote
on 07/17/19 at 08:24:55:
ohiomoto wrote
on 07/17/19 at 06:42:30:
I could be wrong, but I THINK if you remove the lower bushing from the upper, you can remove the seals from the bottom.
http://i178.photobucket.com/albums/w264/punkskalar/LS650%20Savage%20Forks/100...
But with the lower bushing on the tube and the upper bushing and the seal installed in the lower, I don't think you can then slide the lower back on to the tube.
Slide them on to the upper then install after sliding the lower on.
Back to top
Versey's Place
Tech Section Index
IP Logged
oldNslow
Serious Thumper
Offline
SuzukiSavage.com
Rocks!
Posts: 2679
Rochester, NY
Gender:
Re: Having trouble loosening fork legs from crown
Reply #18 -
07/17/19 at 08:49:13
Quote:
Slide them on to the upper then install after sliding the lower on.
OK, I can see that. What do you use to seat the upper bushing in the recess in the lower? I've always used a piece of PVC pipe slid down over the tube to tap it in. Same for the seal.
Back to top
IP Logged
batman
Serious Thumper
Offline
SuzukiSavage.com
Rocks!
Posts: 3806
osceola new york
Gender:
Re: Having trouble loosening fork legs from crown
Reply #19 -
07/17/19 at 09:09:56
I' d remove the top bridge and handlebars and headlight.and turn signals then heat the spacers with a torch ( there alum. and will expand faster than the steel fork tubes) then place a wooden board over the tops of the tube to prevent damage and drive them downward and out . repeating as needed . if the tubes are scratched in the process ,it might be ugly .but the seals don't ride in that area so use shouldn't be affected .
Back to top
my old work mates called me MacGyver
IP Logged
verslagen1
YaBB Moderator
ModSquad
Offline
Where there's a
will, I want to be
in it.
Posts: 28769
L.A. California
Gender:
Re: Having trouble loosening fork legs from crown
Reply #20 -
07/17/19 at 09:23:35
oldNslow wrote
on 07/17/19 at 08:49:13:
Quote:
Slide them on to the upper then install after sliding the lower on.
OK, I can see that. What do you use to seat the upper bushing in the recess in the lower? I've always used a piece of PVC pipe slid down over the tube to tap it in. Same for the seal.
Take and cut a tube in half, length wise would be my 1st guess.
Back to top
Versey's Place
Tech Section Index
IP Logged
ohiomoto
Serious Thumper
Offline
SuzukiSavage.com
Rocks!
Posts: 2690
WTF is JOG?
Re: Having trouble loosening fork legs from crown
Reply #21 -
07/17/19 at 09:39:35
Correct, that's what is called a split seal driver.
They are required for USD (upside down) forks where the axle is mounted on the bottom of the fork and there is no way to slide the seal over it.
You can use saran wrap if you don't have a spare condom lying around and you'll have to be creative with the eeal driver.
Back to top
IP Logged
RocketScienceSmurf
Senior Member
Offline
SuzukiSavage.com
Rocks!
Posts: 268
Sweden
Gender:
Re: Having trouble loosening fork legs from crown
Reply #22 -
07/17/19 at 09:41:15
Just managed to move both spacers a bit. It looks like previous owner put glue or loctite or something EVERYWHERE. (Can't imagine it was done at the factory). The next problem is making the fork legs move in the lower crown. It seem to be just as stuck as the spacers was at first.
Back to top
DSC_1322.JPG
IP Logged
RocketScienceSmurf
Senior Member
Offline
SuzukiSavage.com
Rocks!
Posts: 268
Sweden
Gender:
Re: Having trouble loosening fork legs from crown
Reply #23 -
07/17/19 at 09:55:06
batman wrote
on 07/17/19 at 09:09:56:
I' d remove the top bridge and handlebars and headlight.and turn signals then heat the spacers with a torch ( there alum. and will expand faster than the steel fork tubes) then place a wooden board over the tops of the tube to prevent damage and drive them downward and out . repeating as needed . if the tubes are scratched in the process ,it might be ugly .but the seals don't ride in that area so use shouldn't be affected .
I was contemplating that but I was afraid I wouldn't be able to put everything back together properly. Still, it might be necessary to get the fork legs out from the lower part of the crown.
Back to top
IP Logged
batman
Serious Thumper
Offline
SuzukiSavage.com
Rocks!
Posts: 3806
osceola new york
Gender:
Re: Having trouble loosening fork legs from crown
Reply #24 -
07/17/19 at 12:32:06
Their not from any model of Savage , might be that's why they were glued , because they were off forks 1mm larger.
taking off the top bridge only means removal of the chrome acorn cap , lifting the bars and controls on a padded gas tank surface. the stem and upper and lower bearings stay in place.
Back to top
my old work mates called me MacGyver
IP Logged
ohiomoto
Serious Thumper
Offline
SuzukiSavage.com
Rocks!
Posts: 2690
WTF is JOG?
Re: Having trouble loosening fork legs from crown
Reply #25 -
07/17/19 at 12:42:47
Since you didn't follow my original advice and you appear to have a real mess on your hands, two words: HEAT GUN!
I can remove ahead from a golf club in less than 2 minutes with my heat gun set on high. Maybe add two more words: PIPE WRENCH.
Good luck.
Back to top
IP Logged
RocketScienceSmurf
Senior Member
Offline
SuzukiSavage.com
Rocks!
Posts: 268
Sweden
Gender:
Re: Having trouble loosening fork legs from crown
Reply #26 -
07/17/19 at 13:09:17
ohiomoto wrote
on 07/17/19 at 12:42:47:
Since you didn't follow my original advice and you appear to have a real mess on your hands, two words: HEAT GUN!
Good luck.
I decided I wanted to remove the fork legs, partly because I am not sure I can change the seals myself so I may need to bring them with me to a friend who will assist me if I fail. Also, It think it will be easier if they are removable the next time I need to change the seals for do some other work that normally requires the fork legs to be removed. I did not mean to seem ungrateful.
Back to top
IP Logged
RocketScienceSmurf
Senior Member
Offline
SuzukiSavage.com
Rocks!
Posts: 268
Sweden
Gender:
Re: Having trouble loosening fork legs from crown
Reply #27 -
07/18/19 at 02:14:19
Todays quick investigation has led me to believe tha fork leg is somehow stuck in the top crown plate and not the lower one. Is it only the 29mm nut I have to remove on the top plate?
Back to top
DSC_1326.JPG
IP Logged
ohiomoto
Serious Thumper
Offline
SuzukiSavage.com
Rocks!
Posts: 2690
WTF is JOG?
Re: Having trouble loosening fork legs from crown
Reply #28 -
07/18/19 at 05:51:34
RocketScienceSmurf wrote
on 07/17/19 at 13:09:17:
ohiomoto wrote
on 07/17/19 at 12:42:47:
Since you didn't follow my original advice and you appear to have a real mess on your hands, two words: HEAT GUN!
Good luck.
I decided I wanted to remove the fork legs, partly because I am not sure I can change the seals myself so I may need to bring them with me to a friend who will assist me if I fail. Also, It think it will be easier if they are removable the next time I need to change the seals for do some other work that normally requires the fork legs to be removed. I did not mean to seem ungrateful.
-------------------------------------
Haha, no offense taken here. I was half-joking around and I totally understand your desire to remove the tubes.
Yes, to remove to top clamp, simply remove the center nut. Once removed, you can remove the spanner nut and drop the whole front end.
Back to top
IP Logged
RocketScienceSmurf
Senior Member
Offline
SuzukiSavage.com
Rocks!
Posts: 268
Sweden
Gender:
Re: Having trouble loosening fork legs from crown
Reply #29 -
07/20/19 at 06:31:24
Finally managed to get the fork tubes out of the crown and away from the bike. They were stuck in the top plate pretty hard.
Back to top
DSC_1327.JPG
IP Logged
Pages:
1
2
3
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
05/06/24 at 21:50:49
›
General Category
›
Rubber Side Down!
› Having trouble loosening fork legs from crown
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.