Donate!
Welcome, Guest. Please Login or Register :: View Members
Pages: 1 2 
Send Topic Print
Torque specs List (Read 2351 times)
Ram
Ex Member




Torque specs List
10/06/04 at 17:38:08
 
Compiled a list of torque specs a while ago, to print and put in my garage so I don't have to go thru my manual with greasy hands  Wink

Tekxtc typed the list out in the following post as Ram's web server threw the original list away.

Added excel file -v1
Back to top
« Last Edit: 01/12/17 at 14:25:52 by verslagen1 »  
  IP Logged
tekxtc
Ex Member




Re: Torque specs List
Reply #1 - 11/04/04 at 09:58:32
 
Just in case the page gets lost:
ITEM N-m | ft-lb
Rear
 axle nut
55.0 88.0 | 40.5 64.9
Engine
 drive pulley nut (RH)
100.0 130.0 | 73.7 95.8
Exhaust
 pipe clamp bolts
18.0 28.0 | 13.3 20.6
Front
 axle nut
36.0 52.0 | 26.5 38.3
Front
 axle pinch bolt and nut
15.0 25.0 | 11.1 18.4
Spoke
 nipples
4.0 5.0 | 2.9 3.7
Rear
 driven pulley Mounting nuts
50.0 70.0 | 36.9 51.6
Rear
 driven pulley Side plate bolt
9.0 13.0 | 6.6 9.6
Driven
 pulley nut
100.0 130.0 | 73.7 95.8
Shock
 absorber mounting nuts
20.0 30.0 | 14.7 22.1
Front
 caliper mounting bolts
25.0 40.0 | 18.4 29.5
Front
 caliper pad pin bolt
10.0 15.0 | 7.4 11.1
Front
 caliper bleed valve
6.0 9.0 | 4.4 6.6
Oil
 drain plug
12.0 18.0 | 8.8 13.3
Fork cap
 bolt
35.0 55.0 | 25.8 40.5
Cylinder
 head nuts (9mm)
29.0 33.0 | 21.4 24.3
Cylinder
 head-to-cylinder nuts (8mm)
23.0 27.0 | 17.0 19.9
Cylinder-to-crankcase
 nuts
8.0 12.0 | 5.9 8.8
Rocker
 arm shaft(exhaust) set bolt
8.0 10.0 | 5.9 7.4
Engine
 mounting No. 1 bolts and nuts
37.0 45.0 | 27.3 33.2
Engine
 mounting No. 2 bolt
70.0 88.0 | 51.6 64.9
Engine
 mounting No. 3 bolts and nuts
70.0 88.0 | 51.6 64.9
Engine
 mounting No. 4 bolt and nut
70.0 88.0 | 51.6 64.9
Engine mounting No. 5 Allen
20.0 30.0 | 14.7 22.1
Cylinder
 head cover bolts
8.0 12.0 | 5.9 8.8
Cylinder
 head cover plug
25.0 30.0 | 18.4 22.1
Camshaft
 sprocket bolts
14.0 16.0 | 10.3 11.8
Camshaft
 chain tensioner set bolt
20.0 25.0 | 14.7 18.4
Cam chain
 tensioner/adjuster bolt
8.0 12.0 | 6.0 8.5
Valve
 adjuster locknut
13.0 16.0 | 9.6 11.8
Cylinder
 base nuts
8.0 12.0 | 5.9 8.8
Decompression
 lever nut
15.0 20.0 | 11.1 14.7

Back to top
 
« Last Edit: 06/25/17 at 20:16:08 by verslagen1 »  
  IP Logged
tekxtc
Ex Member




Re: Torque specs List
Reply #2 - 11/04/04 at 09:58:59
 
ITEM N-m | ft-lb
Alternator
 rotor bolt
140.0 160.0 | 103.2 117.9
Primary
 drive gear nut (LH)
90.0 110.0 | 66.3 81.1
Gearshift
 drum stopper
15.0 23.0 | 11.1 17.0
Oil
 filter cap nut & oil sump filter cap bolt
6.0 8.0 | 4.4 5.9
Starter
 clutch Allen bolts
23.0 28.0 | 17.0 20.6
Crankcase
 bolts (6mm)
9.0 13.0 | 6.6 9.6
Oil
 gallery plug (10mm)
12.0 18.0 | 8.8 13.3
Oil
 gallery plug (14mm)
20.0 25.0 | 14.7 18.4
Crankshaft
 hold plug (36mm)
12.0 18.0 | 8.8 13.3
Counterbalancer
 set bolt
40.0 50.0 | 29.5 36.9
Crankshaft
 right end oil seal retainer bolt
5.0 6.0 | 3.7 4.4
Crankshaft
 left-hand flywheel nut
140.0 160.0 | 103.2 117.9
Transmission
 shaft oil seal retainer bolt
9.0 13.0 | 6.6 9.6
Clutch
 locknut
50.0 70.0 | 36.9 51.6
Clutch
 spring bolts
11.0 13.0 | 8.1 9.6
Clutch
 cover bolts
8.8 13.0 | 6.5 9.6
Front
 foot rest nuts
50.0 80.0 | 36.9 59.0
Engine
 ftont mounting bolt nuts
70.0 88.0 | 51.6 64.9
Brake
 disc bolts
18.0 28.0 | 13.3 20.6
Handlebar
 holder bolts & nuts
20.0 30.0 | 14.7 22.1
Handlebar
 clamp bolt
12.0 20.0 | 8.8 14.7
Fork
 bridge clamp bolts
25.0 35.0 | 18.4 25.8
Steering
 stem adjust nut Initial torque
40.0 50.0 | 29.5 36.9
Steering
 stem cap nut
30.0 40.0 | 22.1 29.5
Front
 fork bolt
35.0 55.0 | 25.8 40.5
Front
 fork allen bolt
25.0 35.0 | 18.4 25.8
Swing
 arm pivot bolt and nut
50.0 80.0 | 36.9 59.0
Front
 master cylinder clamping bolts
5.0 8.0 | 3.7 5.9
Front
 master cylinder union bolts
20.0 25.0 | 14.7 18.4
Engine
 front mounting through-bolt nuts
77.0 88.0 | 56.8 64.9

Back to top
 
« Last Edit: 04/07/12 at 16:53:08 by verslagen1 »  
  IP Logged
verslagen1
YaBB Moderator
ModSquad
*****
Offline

Where there's a
will, I want to be
in it.

Posts: 28890
L.A. California
Gender: male
Re: Torque specs List
Reply #3 - 02/22/13 at 21:01:27
 
Digger wrote on 10/24/12 at 21:21:31:
the following



Here's a way to torque fasteners that are impossible to access with a plain torque wrench:

I've got lots of impromptu torque adapters I use while working on my bikes.  For instance, here are two that I've rigged up to torque the two 6mm nuts that are on the starboard side of the bottom of the cylinder assy.

This one uses a standard 10mm combination wrench.  The open end of the wrench fits perfectly on the drive square of my 3/8" torque wrench:





This one uses a 10mm crow's foot popped onto the drive square of my 3/8" drive torque wrench:





Just get an accurate measurement of the new perpendicular moment arm and do the math.  The offset angle of the 10mm wrench is small enough such that it can be neglected, by my calculations.

I keep the conversion factors in a book in my garage.  I currently have nineteen different torque adapters listed in that book.

Back to top
 
 
WWW   IP Logged
verslagen1
YaBB Moderator
ModSquad
*****
Offline

Where there's a
will, I want to be
in it.

Posts: 28890
L.A. California
Gender: male
Re: Torque specs List
Reply #4 - 04/17/13 at 20:32:25
 
another precision torque wrench
Torque = force x distance
measure from the center of the bolt/nut to the center of the hook.
Back to top
 
 
WWW   IP Logged
sbrice54
YaBB Newbies
*
Offline

SuzukiSavage.com
Rocks!

Posts: 39
sheboygan, wi
Re: Torque specs List
Reply #5 - 04/19/13 at 14:35:08
 
Okay Vers..thanks for the tip!! I have used the crows foot..but adding the wrench to the end of the torque wrench are you not adding to the length of the beam therefore increasing the torque? I'm not talking smart. I usually use the "magic" torque wrench in my arm but crucial specs might be skewed. The crows foot I have used myself and extensions for sockets shouldn't change the readings as long as your not adding to the length. Just something I was taught.
Back to top
 
 
  IP Logged
Digger
Serious Thumper
2005 No Login
*****
Offline

Ya gotta be tough to
ride singles!

Posts: 1604
Colorado Springs, CO
Gender: male
Re: Torque specs List
Reply #6 - 04/20/13 at 18:45:51
 
sbrice54 wrote on 04/19/13 at 14:35:08:
Okay Vers..thanks for the tip!! I have used the crows foot..but adding the wrench to the end of the torque wrench are you not adding to the length of the beam therefore increasing the torque? I'm not talking smart. I usually use the "magic" torque wrench in my arm but crucial specs might be skewed. The crows foot I have used myself and extensions for sockets shouldn't change the readings as long as your not adding to the length. Just something I was taught.


Actually, the crow's foot does change the length, just not as much as the wrench does.

To get the proper torque, ya gotta do the math, in both cases.....
Back to top
 
 

Digger
2001, Metallic Glacial Blue, Raptor Petcock, Verslavy (first hole) (otherwise, mechanically, the bike is stock), 13,xxx miles
I don't own a cage.
www.astronautbiker.com
WWW   IP Logged
Jsud04
Full Member
***
Offline

SuzukiSavage.com
Rocks!

Posts: 223

Re: Torque specs List
Reply #7 - 10/09/13 at 04:17:59
 
Spark plug torque for aluminum head?
Back to top
 
 

1986 red, raptor petcock, cham chain tensioner mod,carb plug pulled. DIY highway pegs, DIY ammo can storage...
  IP Logged
verslagen1
YaBB Moderator
ModSquad
*****
Offline

Where there's a
will, I want to be
in it.

Posts: 28890
L.A. California
Gender: male
Re: Torque specs List
Reply #8 - 10/09/13 at 12:00:12
 
Jsud04 wrote on 10/09/13 at 04:17:59:
Spark plug torque for aluminum head?


Torque is specified as being a quarter turn when new, and eighth turn when used.
Back to top
 
 
WWW   IP Logged
Digger
Serious Thumper
2005 No Login
*****
Offline

Ya gotta be tough to
ride singles!

Posts: 1604
Colorado Springs, CO
Gender: male
Re: Torque specs List
Reply #9 - 11/09/13 at 18:51:08
 
verslagen1 wrote on 10/09/13 at 12:00:12:
Jsud04 wrote on 10/09/13 at 04:17:59:
Spark plug torque for aluminum head?


Torque is specified as being a quarter turn when new, and eighth turn when used.


Ver,

Assume that your starting point is for the plug to first be finger tightened?
Back to top
 
 

Digger
2001, Metallic Glacial Blue, Raptor Petcock, Verslavy (first hole) (otherwise, mechanically, the bike is stock), 13,xxx miles
I don't own a cage.
www.astronautbiker.com
WWW   IP Logged
Henrik
Junior Member
**
Offline

SuzukiSavage.com
Rocks!

Posts: 70
Sweden, Jönköping
Gender: male
Re: Torque specs List
Reply #10 - 11/14/13 at 01:55:44
 
Camshaft
chain tensioner set bolt      20.0      25.0      |      14.7      18.4
Camshaft
chain tensioner Plate bolt      8.0      12.0      |      5.9      8.8

Refering to the torque spec list wich one of the above is the bolt that holds the plunger?
Back to top
 

Skrmklipp.PNG
  IP Logged
sesamestreet
Full Member
***
Offline



Posts: 122
Mississauga
Gender: male
Re: Torque specs List
Reply #11 - 11/14/13 at 20:15:53
 
Plate bolt.

at least that's what i used  Embarrassed
Back to top
 
 
  IP Logged
verslagen1
YaBB Moderator
ModSquad
*****
Offline

Where there's a
will, I want to be
in it.

Posts: 28890
L.A. California
Gender: male
Re: Torque specs List
Reply #12 - 11/22/13 at 15:12:37
 
Digger wrote on 11/09/13 at 18:51:08:
verslagen1 wrote on 10/09/13 at 12:00:12:
Jsud04 wrote on 10/09/13 at 04:17:59:
Spark plug torque for aluminum head?


Torque is specified as being a quarter turn when new, and eighth turn when used.


Ver,

Assume that your starting point is for the plug to first be finger tightened?

In general, our sparky doesn't need to be torqued.  The class of fit is such that it won't leak and the cyclic pressure won't work the threads so they fatigue and fail.  What needs to happen is compress the washer to prevent ol sparky from walking out.
Back to top
 
 
WWW   IP Logged
cvsdave
YaBB Newbies
*
Offline

SuzukiSavage.com
Rocks!

Posts: 3

Re: Torque specs List
Reply #13 - 10/16/16 at 21:30:23
 
Why are there two values for both metric and english values in the list:

value1  value2 | value3 value4
Back to top
 
 
  IP Logged
verslagen1
YaBB Moderator
ModSquad
*****
Offline

Where there's a
will, I want to be
in it.

Posts: 28890
L.A. California
Gender: male
Re: Torque specs List
Reply #14 - 10/16/16 at 21:31:43
 
cvsdave wrote on 10/16/16 at 21:30:23:
Why are there two values for both metric and english values in the list:

value1  value2 | value3 value4


it's a range, hi-low.
Back to top
 
 
WWW   IP Logged
Pages: 1 2 
Send Topic Print


« Home

 
« Home
SuzukiSavage.com
10/05/24 at 11:53:01



General CategoryTechnical Documents/Reference › Torque specs List


SuzukiSavage.com » Powered by YaBB 2.2!
YaBB © 2000-2007. All Rights Reserved.