Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› 2 questions help please
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages: 1
2 questions help please (Read 58 times)
sal
YaBB Newbies
Offline
SuzukiSavage.com
Rocks!
Posts: 7
2 questions help please
06/25/14 at 18:40:30
1st question is how do I make my stock exhaust louder. I'm thinking about drilling holes. If this is a possible route where should I drill? Second where is the fuel air screw? Thanks for any assistance.
Sal
Back to top
IP Logged
sal
YaBB Newbies
Offline
SuzukiSavage.com
Rocks!
Posts: 7
Re: 2 questions help please
Reply #1 -
06/25/14 at 18:42:50
Sorry I didn't specify I have a 2004 savage.
Back to top
IP Logged
verslagen1
YaBB Moderator
ModSquad
Offline
Where there's a
will, I want to be
in it.
Posts: 28886
L.A. California
Gender:
Re: 2 questions help please
Reply #2 -
06/25/14 at 18:49:27
all QUESTIONS about the savage go in rubber side down.
Back to top
Versey's Place
Tech Section Index
IP Logged
S-P
Serious Thumper
Offline
Back in the saddle
again
Posts: 816
Phoenix, AZ
Gender:
Re: 2 questions help please
Reply #3 -
06/25/14 at 19:05:04
Sal, (and all noobies)... check out the "Tech documents" on the home page. There are TONS of links to threads about stuff, all categorized: carb/fuel, exhaust, etc. etc. Get familiar with the resources on the site, there's a LOT of cool info on it.
This link is from that list of links
http://suzukisavage.com/cgi-bin/YaBB.pl?num=1221818822/0#0
Back to top
IP Logged
engineer
Serious Thumper
Offline
SuzukiSavage.com
Rocks!
Posts: 872
Gender:
Re: 2 questions help please
Reply #4 -
06/25/14 at 19:12:44
Quote:
Second where is the fuel air screw?
The air screw is located on the right side of the carb, under a brass plug. The way to access it is to very carefully drill a hole into the brass plug, it is about the thickness of a nickel. Then run a sheet metal screw or something similar into that hole and pry/pull the plug out. You will then see the adjustment screw down in the recess.
Quote:
I'm thinking about drilling holes. If this is a possible route where should I drill?
Some have drilled holes and were satisfied with the results. There are good pictures somewhere in the forum. I think, but am not sure, that most drill four or five 3/16 inch holes in the back plate at the back end of the muffler. I don't remember if they put them inside or outside the circle defined by the rivets.
Back to top
2005 S40, Intruder shocks, Dyna, 52.5/150, 3 washers, 2 turns, modified seat, Raptor
IP Logged
Pages: 1
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
09/28/24 at 18:29:50
›
General Category
›
Rubber Side Down!
› 2 questions help please
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.