SuzukiSavage.com - Baron Risers?

Bubbasan YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 23 Champaign, Il Gender:	Baron Risers? 01/28/11 at 21:32:57 Has anyone installed Baron risers? I am wanting the shortest I can find that will fit and looking at the 4" BA-7410U. They have some bolt kits like the BA-7411-U which has a 1/2-13 top, but I'm not sure if the bottom shaft and threads are M10 or if they are long enough. Or does anyone have other riser suggestions for use with drag bars?
Back to top	IP Logged

verslagen1

YaBB Moderator
ModSquad

Offline

Where there's a
will, I want to be
in it.

Posts: 28884
L.A. California
Gender: male

Re: Baron Risers?
Reply #1 - 01/28/11 at 21:57:21

What risers or bar clamps do you have?
If you have the short bar clamps (no risers) and want to spend a lot less, go buy some 3/8" drive 3/4 sockets and a couple 3/8 diameter bolts, length as required. The metric bolts don't fit thru the 3/8" drive.

Otherwise, ask for the 10mm bolts and they should work.

Another option, Z-bars with the short bar clamps. I like less pull back than the stock drags and wider. I found a set of z bars that I like, I guess just like what you're looking for.

Back to top

Versey's Place
Tech Section Index

IP Logged

Serowbot YaBB Moderator ModSquad Offline OK.... so what's the speed of dark? Posts: 28625 Tucson Az Gender:	Re: Baron Risers? Reply #2 - 01/28/11 at 23:37:05 4" is the shortest?... Make some... Mine are BMX bicycle footrests, cut down to size... I coulda' gone shorter, but I wanted my bars to turn down at the ends...
Back to top	Ludicrous Speed !... ... ... IP Logged

MotoBuddha Serious Thumper Offline Let's roll! Posts: 1416 Charlotte, NC	Re: Baron Risers? Reply #3 - 01/29/11 at 08:56:11 Wouldn't the shortest risers would be no risers at all?
Back to top	Travel kills ignorance. IP Logged

Serowbot YaBB Moderator ModSquad Offline OK.... so what's the speed of dark? Posts: 28625 Tucson Az Gender:	Re: Baron Risers? Reply #4 - 01/29/11 at 09:19:44 MotoBuddha wrote on 01/29/11 at 08:56:11: Wouldn't the shortest risers would be no risers at all? Well,... yea... But, drag bars will hit the tank without about a 3" rise... ... unless you angle them up at the ends... awkward...
Back to top	Ludicrous Speed !... ... ... IP Logged

Bubbasan YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 23 Champaign, Il Gender:	Re: Baron Risers? Reply #5 - 01/29/11 at 13:30:07 The bike axel pegs are very nice and creative. I tried to think of alternative risers but couldn't come up with them. Your bike looks great.
Back to top	IP Logged

BarneyBWilde Junior Member Offline Adrenaline does it every time! Posts: 80 Down by the Gulf in Texas! Gender:	Re: Baron Risers? Reply #6 - 01/30/11 at 08:45:26 I went to lowes and bought 1 1/2" spacers and some longer bolts. Altogether I maybe spent 10 bucks.... bolts were a little to long all they had
Back to top	IP Logged

Serowbot YaBB Moderator ModSquad Offline OK.... so what's the speed of dark? Posts: 28625 Tucson Az Gender:	Re: Baron Risers? Reply #7 - 01/30/11 at 10:38:51 Barney,.. those look nice... Are the spacers,.. sockets?... What size?... Do your bars clear the tank at full lock?...
Back to top	Ludicrous Speed !... ... ... IP Logged

einheit13 Full Member Offline SuzukiSavage.com Rocks! Posts: 116	Re: Baron Risers? Reply #8 - 01/30/11 at 15:34:40 Drags hit the tank.......So you get some offset harley risers......1 1/2 rise, 1 1/2 offset $44.99
Back to top	www.soviet-steel.com IP Logged

Bubbasan

YaBB Newbies

Offline

SuzukiSavage.com
Rocks!

Posts: 23
Champaign, Il
Gender: male

Re: Baron Risers?
Reply #9 - 01/30/11 at 17:50:30

Are you sure those will work? I tried these and they just hit the tank.

Here are the ones I have been looking at. 4" rise, 1 1/2" pullback.

These are Baron. Baron also has 1/2-13 to 10MM bolts but I haven't found out if they are long enough. The Baron risers are the ones I was inquiring about. I am still going to look into these but may end up taking Serowbots approach.

Back to top

IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28884 L.A. California Gender:	Re: Baron Risers? Reply #10 - 01/30/11 at 19:20:38 Here's a nice set of drag bars for you, no risers needed... http://cgi.ebay.com/ebaymotors/SANTEE-CHROME-5-RISE-DRAG-BAR-HANDLEBAR-HARLEY... or here's the z bars I think I got... http://cgi.ebay.com/ebaymotors/JAMMER-WIDE-STYLE-CHOPPER-Z-BARS-4-RISE-HARLEY...
Back to top	Versey's Place Tech Section Index IP Logged

einheit13

Full Member

Offline

SuzukiSavage.com
Rocks!

Posts: 116

Re: Baron Risers?
Reply #11 - 01/30/11 at 20:11:38

verslagen1 wrote on 01/30/11 at 19:20:38:

Here's a nice set of drag bars for you, no risers needed...

http://cgi.ebay.com/ebaymotors/SANTEE-CHROME-5-RISE-DRAG-BAR-HANDLEBAR-HARLEY...

or here's the z bars I think I got...
http://cgi.ebay.com/ebaymotors/JAMMER-WIDE-STYLE-CHOPPER-Z-BARS-4-RISE-HARLEY...

The first link is for XLX bars...nowhere near like a drag bar. They are more of a 'mid length' buck horn that really pulls back. The angle sucks....Heres how they sit so the grips are 'level'...I sold them for $10 shipped just to get them outta the garage...this guy likes them, but he likes a very upright riding position

Back to top

www.soviet-steel.com

IP Logged

BarneyBWilde

Junior Member

Offline

Adrenaline does it
every time!

Posts: 80
Down by the Gulf in Texas!
Gender: male

Re: Baron Risers?
Reply #12 - 01/31/11 at 03:26:12

Serowbot wrote on 01/30/11 at 10:38:51:

Barney,.. those look nice...
Are the spacers,.. sockets?... What size?...
Do your bars clear the tank at full lock?...

They are spacers, I'm not sure the Diameter just know that they are 1 1/2" long . My bars do not clear the tank but not enough to where it worries me. I got the idea from the blue collar bobbers site because thats what size spacers come with their kit.

Back to top

IP Logged

Pascal YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 10 France Gender:	Re: Baron Risers? Reply #13 - 08/26/12 at 01:52:22 My new handle bar Width drag bar is 700 mm. Two home made spacers of 55 mm (the handle bar not hit the tank). Two home made screws of 125 mm length and 10 mm diameter. But the view in the mirors is bad, so I would like to change them in future
Back to top	IP Logged

arteacher Serious Thumper Offline Ride as if your naked and invisable! Posts: 2581 London ontario Gender:	Re: Baron Risers? Reply #14 - 08/26/12 at 06:56:20 I just ordered these for the Builtwell risers. They are 1" 1/2-13, 1" 10mm shank, and 1" 10mm threaded. http://www.jpcycles.com/product/ZZ50386
Back to top	white '07, Raask exh, Corbin seat, slipstreamer shie, Raptor, Routy's fwd controls, Baron tach, Frisco bars, Isogrips, Headlight and taillight modulators, Dial-a- jet, AME 9 deg chop kit, K&N air flt IP Logged