Donate!
Welcome, Guest. Please Login or Register :: View Members
Pages: 1
Send Topic Print
Idle Mix Screw Brass Plug removal  (with Pics) (Read 4034 times)
EssForty
Senior Member
****
Offline

Sunshine, Surf &
Suzuki

Posts: 382
Melbourne, FL
Gender: male
Idle Mix Screw Brass Plug removal  (with Pics)
09/19/08 at 03:07:02
 
PLEASE NOTE: the idle screw plug modifications described only apply to SOME country versions - check the pics below. Not all Savages have the plug. "




A stock S40 Boulevard is tuned very lean to meet EPA emissions standards. It also pretty much guarantees a significant amount of afterfiring (or backfiring to most people). To correct the afterfire problem, you'll have to remove the brass plug that Suzuki installs to cover the idle mixture screw.

The process is very simple and the results are remarkable. In the picture above at about the 2 o'clock position on the right side of the carb you'll see a small brass plug. What you want to do is remove this plug to expose the idle mixture screw beneath it. Do not confuse this with the idle "speed" screw, which sets the idle rpm's higher. When you adjust the idle speed screw you're making a lean fuel mix idle faster.  When you adjust the idle "mixture", you're going to add more fuel to the mix, thereby running more "rich".

The way you'll remove the plug is to drill a shallow pilot hole, then drive in a screw for a few turns until it wedges in firmly, and then you'll pull out the screw and the plug together.

Step 1: Drill the pilot hole with a 3/32" bit. Be carefull to limit the depth to about 1/8"-3/16" deep. You can wrap tape around your bit at the desired depth so you don't end up drilling thru the idle mix screw.


Step 2: Screw a fine drywall screw into the pilot hole until it is firmly gripping the brass. You do not usually need more than a full turn or two.



Step 3: Grab the screw with a pair of vice grips and pull it out. Takes a little effort.



Step 4: When the plug is removed, clean out any brass shavings that may remain inside, and then give the exposed idle mixture screw a half-turn counter-clockwise .  A half turn works well for most people as a starting point. You may need more if you are at a different altitude, temp or humidity.

If you have a tachometer, you can fine tune it further by adjusting the screw until you reach max rpms. Turn it 1/4 turn at a time, wait 20 seconds and see if the revs go up.  If they do, give it another 1/4 turn, wait 20 secs and repeat until the revs drop. Turn it back as needed to hit the peak.



Also, after-firing can also be aggravated by air inleakage at the exhaust header, Be sure to check that your header nuts are tight before you test out the new setting.

You're set. You should see a big reduction in afterfiring and for normal driving you should not expect a penalty in mpg. If you're idling in stop and go traffic a lot, it may reduce your fuel efficiency.


One last thought... it is possible that you may have to adjust your idle SPEED screw, on the other side of your carb,  after this mod.  I had mine tuned to idle at 1000 rpms with the leaner fuel mix. After I richened the mix the bike cut off at idle when I went for a test ride.  So if this happens to you, don't go in there and adjust your fuel mixture first. Just crank up the idle speed a bit and you should be fine.  
Back to top
 
« Last Edit: 04/19/14 at 09:41:52 by Serowbot »  

06 S40, Deuce shield, OEM saddlebags & Engine Guard, ENM tach, Sigma 1106 Speedo, oil pressure & voltage gauges, grip puppies, Kuryakyn Ellipse mirrors, ISO pegs & throttle boss
  IP Logged
Uno-Lung
YaBB Newbies
*
Offline

all great things are
simple

Posts: 27
Kalamazoo
Gender: male
Re: Idle Mix Screw Brass Plug removal  (with Pics)
Reply #1 - 04/26/12 at 14:31:33
 
I thought I should share this with all the members here as I have gleaned so much information from this site and have read so many posts of the butchery of this little plug and the adjustment screw behind its brassy stubbornness.

Well, after reading the above post and following the instructions to the letter, I thought I was going to die.  The death vice-grip trick just was not going to work.  Afraid that I was going to rip the carb off the bike roots and all, or pop a gut -- I was resigned to the fact that my first  two attempts were not worth my tinker’s damn.  I lamented my predicament down at the coffee shop the next morning and one of my fellow coffee addict friends said I should try his body dent puller tool.  Needless to say, after the first half-hearted pull and next one rewarded me with the desired result.  Thanks to all.



Back to top
 
 

"You can't change the world but at least you can try and put a dent in it!" Smootchy
  IP Logged
NHLycan
Junior Member
**
Offline

Nice forum!

Posts: 86
New Hampshire
Gender: male
Re: Idle Mix Screw Brass Plug removal  (with Pics)
Reply #2 - 08/27/13 at 15:47:55
 
I pulled out the plug tonight as I scared the neighbors kid with a kaboom and it stopped being funny to me.
Embarrassed
They had glued it in place but one sharp tale back on the pliers with a small hammer and out she came. 1.5 back and the kaboom appears to be no more.  Smiley
Maybe no less, I guess time will tell.
Back to top
 

IMG_0697.jpg

New Hampshire. 2003 SL650. 13k miles. Raptor installed. Versy adjuster. Rotella 6 w/zinc. Idle mix plug out. Seat front up 1". Owned since July 2013. Mechanically inclined. Better cook than mechanic.
  IP Logged
thelowfreq
YaBB Newbies
*
Offline

SuzukiSavage.com
Rocks!

Posts: 13

Idle Mix Screw Brass Plug removal SUCCESS!
Reply #3 - 10/26/13 at 16:41:17
 
I  just  drilled out the  cover to the  Idle Mix adjusting screw..it was  a lot easier than I expected.    Why don't the  dealers  do this  mod?     It runs    a  lot better ,doesn't   "pop"   on gear changes      but  still does  a dog fart  when I shut it down.   next  I'll do some fine tuning       Thanks for the   info!
Back to top
 
 
  IP Logged
oldNslow
Serious Thumper
*****
Offline

SuzukiSavage.com
Rocks!

Posts: 2686
Rochester, NY
Gender: male
Re:  Idle Mix Screw Brass Plug removal SUCCESS!
Reply #4 - 10/27/13 at 17:11:41
 
thelowfreq wrote on 10/26/13 at 16:41:17:
I  just  drilled out the  cover to the  Idle Mix adjusting screw..it was  a lot easier than I expected.    Why don't the  dealers  do this  mod?     It runs    a  lot better ,doesn't   "pop"   on gear changes      but  still does  a dog fart  when I shut it down.   next  I'll do some fine tuning       Thanks for the   info!


Most dealers won't tamper with adjustments related to exhaust emissions for legal reasons.
Back to top
 
 
  IP Logged
Dave
YaBB Moderator
ModSquad
*****
Offline

SuzukiSavage.com
Rocks!

Posts: 18139
Camp Springs, Kentucky
Gender: male
Re: Idle Mix Screw Brass Plug removal  (with Pics)
Reply #5 - 10/29/13 at 07:38:19
 
It doesn't state the penalty.....but here is information that makes it clear you (including dealers) are not supposed to tamper with the emission controll devices.  I would interpret this to mean jet changes and pulling out devices that are installed specifically so you don't make any changes.

http://www.epa.gov/otaq/regs/roadbike/420f03045.pdf

There may come a day when your bike is inspected and won't be licensed if you have (tampered with) removed the brass plug.....and maybe even tailpipe  testing for emissions.  KY did that for a little while in the Boon/Campbell/Kenton county areas for passenger cars and trucks - but they have abandoned it.  
Back to top
 
« Last Edit: 09/22/15 at 04:33:15 by Dave »  

Someday I will be old......But not today!

  IP Logged
oldNslow
Serious Thumper
*****
Offline

SuzukiSavage.com
Rocks!

Posts: 2686
Rochester, NY
Gender: male
Re: Idle Mix Screw Brass Plug removal  (with Pics)
Reply #6 - 10/29/13 at 09:00:34
 
Quote:
There may come a day when your bike is inspected and won't be licensed if you have removed the brass plug.....


I think we are lucky in that motorcycles are still kind of under the radar in most places as far as strict compliance with the laws goes.  For example, this is from the NYS inspection regs:

Quote:
No person shall operate on any highway a motorcycle which is:
not equipped with a muffler to prevent excessive or unusual noise;
equipped with a muffler from which the baffle plates, screens or other original internal parts have been removed or altered;
equipped with an exhaust device without internal baffles, known as “straight pipes”;
equipped with a modified exhaust system that amplifies or increases the exhaust noise so it is louder than the noise made by the original exhaust system.Equipped with a muffler intentionally designed to allow for the internal baffling to be fully or partially removed or interchangeable (1979 and newer motorcycles).


If that one was enforced there would hardly be a Harley in the state with a legal inspection sticker or registration. In fact most Harley dealers are more than happy to sell you a six or seven hundred dollar set of pipes for your brand new bike, charge you another hundred or so to remap the fuel injection, slap on an inspection sticker and send you out the door.

I'm not complaining about this - I think you should be able to do whatever you want to your motorcycle - but I do find it a bit ironic.

I've got two 1/2 inch holes drilled in the end of my muffler courtesy of the previous owner, and the idle mixture plug is gone too. No one doing the yearly inspections has ever paid any attention.

Back to top
 
 
  IP Logged
Dave
YaBB Moderator
ModSquad
*****
Offline

SuzukiSavage.com
Rocks!

Posts: 18139
Camp Springs, Kentucky
Gender: male
Re: Idle Mix Screw Brass Plug removal  (with Pics)
Reply #7 - 04/24/18 at 07:29:23
 
Off topic replies have been moved to this thread.
Back to top
 
 

Someday I will be old......But not today!

  IP Logged
buster6315
Senior Member
****
Offline

SuzukiSavage.com
Rocks!

Posts: 354

Re: Idle Mix Screw Brass Plug removal  (with Pics)
Reply #8 - 09/02/21 at 20:35:00
 
Dave wrote on 10/29/13 at 07:38:19:
It doesn't state the penalty.....but here is information that makes it clear you (including dealers) are not supposed to tamper with the emission controll devices.  I would interpret this to mean jet changes and pulling out devices that are installed specifically so you don't make any changes.

http://www.epa.gov/otaq/regs/roadbike/420f03045.pdf

There may come a day when your bike is inspected and won't be licensed if you have (tampered with) removed the brass plug.....and maybe even tailpipe  testing for emissions.  KY did that for a little while in the Boon/Campbell/Kenton county areas for passenger cars and trucks - but they have abandoned it.  

I've noticed that my recently purchased '08 Savage tends to 'surge' when riding at partial throttle, and pops on deacceleration, so I removed the plug and opened the pilot screw one half turn.  Have to wait for clear weather before seeing if it helped: Around these parts Labor Day Weekend is 80% chance of precipitation)  Sad
Back to top
 
 
  IP Logged
buster6315
Senior Member
****
Offline

SuzukiSavage.com
Rocks!

Posts: 354

Re: Idle Mix Screw Brass Plug removal  (with Pics)
Reply #9 - 09/05/21 at 16:00:25
 
I opened the jet screw 1/2 turn;  no change in the surge at crusing/throttle just cracked open.  If I pull the choke out the surge goes away, so I'm thinking its starving for fuel.  But its in compliance with the epa!
Back to top
 
 
  IP Logged
verslagen1
YaBB Moderator
ModSquad
*****
Offline

Where there's a
will, I want to be
in it.

Posts: 28905
L.A. California
Gender: male
Re: Idle Mix Screw Brass Plug removal  (with Pics)
Reply #10 - 09/05/21 at 20:28:24
 
Replace the white spacer with 3 #4 washers or shave the white spacer .02 to .03"
Back to top
 
 
WWW   IP Logged
buster6315
Senior Member
****
Offline

SuzukiSavage.com
Rocks!

Posts: 354

Re: Idle Mix Screw Brass Plug removal  (with Pics)
Reply #11 - 09/05/21 at 20:37:04
 
Thank you.  Of course to access the carb I'll have to remove the gas tank.  Not sure when the spirit will move me to work on it.
Back to top
 
 
  IP Logged
Pages: 1
Send Topic Print


« Home

 
« Home
SuzukiSavage.com
11/08/24 at 09:36:31



General CategoryTechnical Documents/Reference › Idle Mix Screw Brass Plug removal  (with Pics)


SuzukiSavage.com » Powered by YaBB 2.2!
YaBB © 2000-2007. All Rights Reserved.