Donate!
Welcome, Guest. Please Login or Register :: View Members
Pages: 1 2 3 ... 5
Send Topic Print
Chain coversion for the Savage/S40 (Read 7735 times)
Hutch
Serious Thumper
*****
Offline

till death do us
part

Posts: 1035
Birch Run, MI. U.S.A.
Gender: male
Chain coversion for the Savage/S40
03/18/07 at 10:35:33
 
Following is the list for the parts needed. The sprockets are JT Sprockets items. All you need to order(available from several sources) is the front and rear sprockets for a Suzuki 1980 GS550 with CAST wheel. These sprockets are available in 13- 18 for the front sprocket. The 18 will not have enough clearance but the rest are fine. The rear are available in 38-52 and will all work. You will need to order an extra 13 tooth front sprocket. This will be needed to make a spacer. I cut a 40mm circle out of the 13 tooth, and it fits on the outside of the sprocket to take up the room between the sprocket and the toothed lock washer and the nut that tightens everything down. It is a simple switch. After putting bike in gear(5th) Just remove all the belt covers, and the cover for the front pulley(three 8mm bolts) Place a steel bar(wrapped with tape) through the spokes of rear wheel and on TOP of your swing arm on both sides. A32mm socket is needed to remove nut on the front pulley(lefty loosie). Be sure to flatten the lock washer that is bent over nut first. After that loosen chain adjusters, loosen axle and move rear wheel forward. Pull the rear axle out and the spacers, be sure to remove back brake cable adjuster and barrel. Now you can pull out the bottom shock bolt(pulley side) and swing shock out of the way to remove belt. Remove the pulley off the rear wheel(six 14mm nuts) and replace with sprocket of your tooth choice. Slide the sprocket of your choice on the transmission shaft, slide on the spacer made from the 13 tooth sprocket, the toothed washer and finally the nut. You may need to JUST grind the spacer a very little to allow room for the toothed washer to slide on the tranmission spline. I used a disk sander, and took ONLY enough metal off to let the toothed washer to hang on the splines. After that you just bolt everything back up and figure out the length of your chain. I used a 530 chain of 110 links, and took links out(2) to fit my sprocket combo(17/43) You will NOT be able to run a belt guard(brackets on swing arm will hit chain) in some cases when using an o-ring chain, because it is wider. With a normal chain there is no problem, even down to the 14 tooth on the front. If you do not run a belt/chain guard you will need to put an extra washer on the bottom shock bolt to take up the space of the belt guard. Just take a washer with a large enough hole to fit bolt and cut out one side making it look like a "u". This way you can run gaurd or not and will not have to remove rear wheel to take out the washer.  The cost for the whole chain coversion with NEW sprockets from the DEALER was $95. This included a cheap chain, until I find the best ratios for me. Once I find the ratio I like best, I will go with a good o-ring chain that will add to the cost . $70 for sprockets and the price of a good chain is a good deal to be able to DIAL in what you want your Savage to do.     I will be posting pics later.   HAVE FUN!!! with all the ratios you have to play with. You can now cruise the interstate at lower RPM's or turn your Savage into a street rocket that will pull the front tire off the road all day. It's all up to YOU!!!  and the sprockets you choose. Hutch  
Following are pics of conversion. This one shows spacer behind the washer and nut.



This shows how close chain runs to belt guard bracket. The smaller 14 tooth sprocket might mean removing bracket.  

 

This shows the sprocket I cut the 40mm OD center out of to make the spacer for behind the washer and nut.  

 

Here is a look down the chain.  

 

This the complete view. Just put covers on, and enjoy!!  

 

Here is a chart showing the difference in RPM at the same speed, comparing stock gearing on left and new gearing on the right.  

--stock--------------------------------------new ratio 17/43 ----
50mph@3111---------------------50@2660rpm=450less-----
60mph@3733---------------------60@3193rpm=541less-----
70mph@4355---------------------70@3724rpm=631less-----
80mph@4977---------------------80@4255rpm=722less-----
90mph@5600---------------------90@4788rpm=812less-----
100mph@6222------------------100@5320rpm=900less-----
105mph@6500------------------105@5560rpm=940less-----

Here is another chart for a different ratio.

--stock------------------------------------new ratio17/45--------
50mph@3111--------------------50@2799rpm=312less------
60mph@3733--------------------60@3359rpm=374less------
70mph@4355--------------------70@3919rpm=436less------
80mph@4977--------------------80@4479rpm=518less------
90mph@5600--------------------90@5040rpm=560less------
100mph@6222-----------------100@5600rpm=622less------
105mph@6500-----------------105@5850rpm=650less------

That is just two examples of what you can do by changing gear ratios and how it affects your rpm and mph. Keep in mind that a one tooth change on the REAR sprocket is a 2.5% change in gearing. For every one tooth change on the FRONT sprocket it is a 5-6% change in gearing.  
 HAVE FUN!!!   Hutch

Back to top
 
« Last Edit: 12/08/12 at 13:10:00 by Oldfeller--FSO »  

you learn from your mistakes, and I've learned a lot
  IP Logged
tbalam
Full Member
***
Offline

I like my kids, but
I love my bike ;)

Posts: 172
Fac o' the Sn
Gender: male
Re: Chain coversion for the Savage/S40
Reply #1 - 03/18/07 at 11:12:01
 
Hey guys,

These sprockets fit a number of models and years. Most of the sprockets for the GS, GSXR, GSX's work.

Hear is the model numbers:

JTsprockets Front: jtf513.?
                   Rear  jtr816.?

The .? is for whatever tooth number you want.


If you go here:
http://www.jtsprockets.com/61.0.html?&L=0&sel_artnr=JTF513,13

And here:
http://www.jtsprockets.com/61.0.html?&L=0&sel_artnr=JTR816,39

You can see at the links above all the models that share these sprocket designs and then buy a sprocket for anyone of these models, from whatever sprocket manufacturer you want.

Like hutch i went with a 17/43

you can buy most of the parts on ebay. I paid 15 bucks for the rear and 60 bucks for an oring chain. shipping included




Back to top
 
 

1996 Mirage paint, seat lift, 2 #4 washers, 155 main, 52.5 pilot. Removed pillon, belt guard, rear blinker mod, moved battery box. K&N cone, Chain conversion 17/43 (in process). Cam tensioner mod.
  IP Logged
Savage_Greg
Serious Thumper
Alliance Member
*****
Offline

Don't go around your
ass to reach your
elbow...

Posts: 7844
SW Washington State
Gender: male
Re: Chain coversion for the Savage/S40
Reply #2 - 03/19/07 at 09:10:22
 
And if I may add a bit to this....

If you want to shop different prices and manufacturers, the Motorcycle Superstore carries 3 brands of sprockets that fit the Suzuki GS550 model....and other Suzukis too.

At this time the Motorcycle Superstore has 2 day shipping and free for orders over $75...that'll get both sprockets and chain, delivered for free.

The brands are AFAM, Sunstar, and JT Sprockets.  The JTs are the cheapest...and cheaper than my dealer too.  Go here for the sprocket list.

http://www.motorcycle-superstore.com/PartsByDept.aspx?DID=759&Type=1

Go here for the chain list.

http://www.motorcycle-superstore.com/Department.aspx?Department=660&Division=6

Sprocket ratios to go with Hutch's charts are:

45/17 = 2.65
43/17 = 2.53
45/16 = 2.81
43/16 = 2.69

(stock pulleys are 68/23 = 2.956)

I chose mine from the GS550L model with the 17/45 set and 120 link 530 Roller Chain (cheap like Hutch) to make a little different comparison.  

My shopping cart is now ready for next payday.  Total cost $83.97 with free shipping Tongue
Back to top
 
 


  IP Logged
Hutch
Serious Thumper
*****
Offline

till death do us
part

Posts: 1035
Birch Run, MI. U.S.A.
Gender: male
Re: Chain coversion for the Savage/S40
Reply #3 - 03/22/07 at 18:28:29
 
I put over 100 miles on the 17/43(2.53 ratio) conversion and really got the feel today. In town it is a 3rd gear no jerk affair at 25mph. 4th gear for towns with 35-40 speed limits. Back roads are an easy smooth rpm at 55-60(speedo reads 48-51) going with the traffic. On the interstate at 70-75 (speedo reads 60-65) it is a joy now. It falls into a super smooth rpm where the exhaust note  gets hard to hear without leaning that way to hear it., and I have the loud Jardine muffler. SMOOOTH. Passing a semi is no problem, even in the turbulance at the cab door of the truck. Down shift only needed if a heavy head wind. The best way I can describe the all around performance of the bike with this ratio is to compare it to another bike. This will not help the younger people on this site, but I know I am not the only middle aged person here. Aceleration is a STEADY, STRONG pull in all gears. with 5th as an overdrive. It feels just like a Triumph 750 twin of the 70's. Only a LOT less vibration. It is perfect. I thought I would be spending most of my time with the 14/43 (3.07ratio)combo on it for everyday driving, and going to the 17 on the front for when I wanted to hit the e-way for long trips. I believe it is going to be 17/43(2.53 ) MOST of the time now, and ONLY switched to the 14/43 (3.07)when I just want to smoke most everything else from 0-60. I can't believe how much nicer a bike it has become. I did get a chance to find out how far my speedo is off. I can't belive I did this, but I saw a State Police Officer at the ramp when I got to the e-way. I told him the story of the conversion and that my speedo was off. He agreed to follow me on to the e-way and let me know when I hit 70mph. The speedo is off by 10mph. When it said 60 mph it was 70.Below 55 it is off by about five mph. I did have it up to a speedo reading of a little over 80mph(95 actual, not with the cop around) and I was in the 3rd lane passing everybody. I came home and figured everything out, and either my speedo has been reading slow to begin with or something. The gear change is a 14.5% change, but the real speed, compared to the speedo reading, works out to a 17% change to be correct. Oh well, all I know is I LIKE IT. It is a much more VERSATILE bike, but that is my oppinion, as much as that is worth. In more hilly country or when carrying more weight(200lb+ rider or carrying passenger) I believe the 17/45 (2.65 ratio), or the 16/43(2.69)would be a better choice. That is why I went with the 43 back sprocket. You can cruise flat land with the 17/43, hilly with the 16/43, and smoke with the 14/43. There is no problem with clutch slippage using the 17/43 conversion, so far.  
RIDE SAFE    Hutch
Back to top
 
 

you learn from your mistakes, and I've learned a lot
  IP Logged
tbalam
Full Member
***
Offline

I like my kids, but
I love my bike ;)

Posts: 172
Fac o' the Sn
Gender: male
Re: Chain coversion for the Savage/S40
Reply #4 - 03/25/07 at 17:52:20
 
Since hutch mentioned clutch slippage, if you go to a gear ratio that is high like 2.5-2.75 it may be an issue.
the springs on the savage are not that good so here are the part numbers for a high friction plates and springs from bike bandit.

Bike bandit sells the vesrah plates and springs for the savage.  

VC330- Plates - 79.95
SK330- springs - 10.95

These should take care of any clutch slippage that is caused by the additional load generated by these gear ratios.

Oh, and the conversion was totally worth it. at 17/43 in fourth gear i am where i used to be in fifth gear. SO now I have an extra gear to play with 80 mph is now an easy lope with still alot more throttle to go.
Back to top
 
 

1996 Mirage paint, seat lift, 2 #4 washers, 155 main, 52.5 pilot. Removed pillon, belt guard, rear blinker mod, moved battery box. K&N cone, Chain conversion 17/43 (in process). Cam tensioner mod.
  IP Logged
Hutch
Serious Thumper
*****
Offline

till death do us
part

Posts: 1035
Birch Run, MI. U.S.A.
Gender: male
Re: Chain coversion for the Savage/S40
Reply #5 - 03/26/07 at 16:54:05
 
Just got back from a mileage check. I used the state map distances and the signs on Interstate 75. 264 miles round trip at an average of 75-80mph, did use third lane on occasion(80-85mph). Total gas consumption, 4.5 gallons.I used to get 50-52 mpg on the back roads(55-60mph) with a 152.5 main and 55 pilot. I am now running a bigger 155 main and flying down the interstate at 75-80mph and getting 58.5mpg.No screaming rpms, just a smooth level groove that it falls into. I must also mention that it was calm when I left this morning, but on the way back I was bucking 20-25mph wind gusts. Even with the wind gust there was no need to downshift to pass any vehicle, just roll on the throttle.On two lane black top at 50-55mph it is just an easy lope, and all that is needed is a twist of the throttle to get a STRONG, STEADY acceleration, no down shift needed. This is the best $95 I ever spent. WHOLE NEW BIKE. The 14 tooth sprocket makes it a little quicker off the line than stock, but I was all the way to end of adjustment and chain was not as tight as it should be. If you ran the 16 tooth(2.69ratio,9%change) and 14 tooth you will be able to use the same chain. I have the feeling that I will DEFINATELY be running the 17/43(2.53ratio,14.5%change) 99.9% of the time. This is just what I was looking for, PERFECT for me.  The change in gearing percentage works out to the same change in fuel consumption I changed my gearing by 14.5%, and increased my MPG by 14.5%  The 16/43(2.69ratio) would be a 9% change in gear ratio from stock and a 9% increase in mpg . At least it should be, going by my change in gearing and change in mpg.  Even if you were to add one of LANCERS cams from Web, you would have more power and possibly get 50mpg.  Later Hutch
Back to top
 
 

you learn from your mistakes, and I've learned a lot
  IP Logged
Savage_Greg
Serious Thumper
Alliance Member
*****
Offline

Don't go around your
ass to reach your
elbow...

Posts: 7844
SW Washington State
Gender: male
Re: Chain coversion for the Savage/S40
Reply #6 - 05/02/07 at 10:17:43
 
45/17 combo with chain from the Motorcycle Superstore with free shipping for orders over $75.00.

Reference sprockets for the Suzuki GS550.

Back to top
 
 


  IP Logged
vroom1776
Serious Thumper
*****
Offline



Posts: 2110

Gender: male
Re: Chain coversion for the Savage/S40
Reply #7 - 06/15/07 at 09:47:26
 
Based on Hutch's numbers for 5th gear, stock tire, I made these theoretical plots for various gear ratios.  The format is Speed (mph) vs rpm.  The vertical black line represents a 6500 rpm redline.  The horizontal black line represents 80 mph.



notice that the 13-37 and the 17-50 are pretty much the same as the stock 23-68.

with the 17-38, you could do about 135 mph, but it would take you forever to get there.
Back to top
 
 
  IP Logged
ThumpinSquid
YaBB Newbies
*
Offline

I love YaBB 1G -
SP1!

Posts: 49
Near Granite Falls & Robe, WA
Gender: male
Re: Chain coversion for the Savage/S40
Reply #8 - 09/21/07 at 09:16:51
 
One last note on rear sprokets. If you're ordering online, then all the info you need is in this thread. If you're like me and support local business ( I do it primarily because I live on top of a mountain and "priority shipping" still takes two weeks) or you have a MC salvage shop you like to go to,

The GS rear sprockets WE need have a 100mm bolt pattern.

I know it says above we need the ones for CAST wheels, but at the shop I went to they have them divided into "spoke" and then all others. I got one for "all others" thinking "spoke" meant wire spoke wheels. We'll, the one I got has a 73mm bolt pattern so I'm headed back today to get the right one, ruler in hand.

Last reminder, LOOSEN THE DRIVE PULLEY NUT BEFORE YOU TAKE THE REAR WHEEL OUT! Or it won't come off at all. I got a little gung-ho and forgot and wasted about an hour. Plus I skinned my knuckles and it really really hurt.

There, now you have no excuses. <$100 and it makes room for bigger tires, let's YOU pick your performance style, and is easily fixed if you have a problem on the side of the road! Throw a chain, toss in another master link, throw a belt, call a tow truck! Smiley

EDIT>>> Instead of buying a 13-tooth front to make a spacer (I don't work in a machine shop anymore and don't have any way to cut it at home) I bought 2 7/8" washers and after 5 minutes with a dremel they fit over the spines just fine. Also, this way I was able to sandwich my drive gear between them to help compensate for the offset of my rear sprocket as a result of the 165R15 tire mod. The nut has a recess that allows it to fit over the splines to press on the spined lock washer too, so it's good to go.
Back to top
 
 

Out of my way, I have to pee!
  IP Logged
bsdnfraje
Full Member
***
Offline

SuzukiSavage.com
Rocks!

Posts: 158

Re: Chain coversion for the Savage/S40
Reply #9 - 05/02/08 at 14:47:19
 
Thumpinsquid mentioned using 2 7/8" washers as spacers.  But he had to dremel them a little to fit.

I picked up 2 1" washers at the local ACE, no dremeling required.  They slip right over the shaft perfectly.

But check the outer diameter. There were two choices at my ACE.  One was perfect, the other was slightly larger overall and I think might have interfered with the chain on my 16 tooth sprocket.

And man I wish I had done this conversion on Day One.  I went to 16/43 and it is awesome.  I would have went 17/43 like some others, but I like going back home in the mountains sometimes.  It doesn't feel, though, like a 17 would keep me from climbing.  I may try it out when time to replace the chain.

I was a little bitter at first because it seemed like nothing had really changed, and then I remembered that the speedo is now off, which explains why the wind resistance was so much stronger at "70mph".

Thanks to Hutch, Thumpinsquid, Savage_Greg and all the guys who contributed to this post.  Its like having a brand new bike.

[edited to add} Also I had to take my rear belt pulley to my local auto shop to break free the six nuts holding it to the hub.  No charge, because we change oil on two vehicles there 3-4 times per year, but it made the conversion simpler.
Back to top
 
« Last Edit: 05/02/08 at 19:27:07 by bsdnfraje »  
  IP Logged
Savage_Greg
Serious Thumper
Alliance Member
*****
Offline

Don't go around your
ass to reach your
elbow...

Posts: 7844
SW Washington State
Gender: male
Re: Chain coversion for the Savage/S40
Reply #10 - 06/12/08 at 07:31:42
 
BTW - I didn't think about it at the time, but the "standard" chain pictured above (and other comparable ones) is rated for street bikes "up to 350 cc" maximum.

Since I'm changing sprockets again, I decided to get a higher rated chain this time.  I bought an EK 530 SROZ o-ring chain instead.  It is rated for bikes up to 50 HP.  It still cost more at $80, but that would be a small issue if I had a chain problem a long distance from home.
Back to top
 
 


  IP Logged
MrThud
YaBB Newbies
*
Offline

SuzukiSavage.com
Rocks!

Posts: 22
Brisbane, Australia
Gender: male
Re: Chain coversion for the Savage/S40
Reply #11 - 01/30/09 at 05:29:15
 
This is an excellent and informative thread, thanks guys.

One item I see missing from the top pic is a locking washer.
You could do this yourself by fitting a large (but thin) washer between the spacer and the nut and then flattening one side down at 90% so that it retains the nut from loosening. (There are other ways of ensuring that the sprocket nut doesnt loosen, but the washer idea is simplest). Note the internal dia of the washer would have to be 'keyed' to fit the shaft splines.
Hope you can picture what im describing. If not ask your buddy with a std sprocket set up to let you have a look at how the sprocket nut is retained.. on Jap bikes it typically is as I described.

best,
G.

Back to top
 
 
  IP Logged
BigSingle
Junior Member
**
Offline

SuzukiSavage.com
Rocks!

Posts: 74
Pensacola Florida
Gender: male
Re: Chain coversion for the Savage/S40
Reply #12 - 02/08/09 at 09:05:19
 
What chain is everyone going with? Im going to asume 525 or 530 bc that is what most kits and stock comes with. I know with my trackbike and most streetbikes you swap to a 520 conversion. It a smaller chain wich is lighter (less restriction/"more power")(could also help w clearence) and it makes a huge difference. Now it is a bit more expencive to buy but there is many diffrent options on chain styles. When swaping to a 520 the maint. and replacemt interval gets shorter bc it will strech quicker, but its not like our bikes put out a ton of power...
Back to top
 
 
  IP Logged
Hutch
Serious Thumper
*****
Offline

till death do us
part

Posts: 1035
Birch Run, MI. U.S.A.
Gender: male
Re: Chain coversion for the Savage/S40
Reply #13 - 02/15/09 at 06:34:23
 
MrThud wrote on 01/30/09 at 05:29:15:
This is an excellent and informative thread, thanks guys.

One item I see missing from the top pic is a locking washer.
You could do this yourself by fitting a large (but thin) washer between the spacer and the nut and then flattening one side down at 90% so that it retains the nut from loosening. (There are other ways of ensuring that the sprocket nut doesnt loosen, but the washer idea is simplest). Note the internal dia of the washer would have to be 'keyed' to fit the shaft splines.
Hope you can picture what im describing. If not ask your buddy with a std sprocket set up to let you have a look at how the sprocket nut is retained.. on Jap bikes it typically is as I described.

best,
G.


The washer behind the nut is the original washer from Suzuki with the little tab you were speaking of and slined. If you look real close by the number 17 on the sprocket, you will see the tab bent over. This is on the first picture you mentioned.  Hutch
Back to top
 
 

you learn from your mistakes, and I've learned a lot
  IP Logged
4drcaddy
YaBB Newbies
*
Offline

SuzukiSavage.com
Rocks!

Posts: 8

Re: Chain coversion for the Savage/S40
Reply #14 - 01/16/11 at 20:29:17
 
i actually made a post on rubber side down but since it was recently being discussed here, did anyone figure out a good number of teeth front and rear for an 87 4spd? looking for close to stock with a little more highway friendly?
Back to top
 
 
  IP Logged
Pages: 1 2 3 ... 5
Send Topic Print


« Home

 
« Home
SuzukiSavage.com
12/07/24 at 22:19:29



General CategoryTechnical Documents/Reference › Chain coversion for the Savage/S40


SuzukiSavage.com » Powered by YaBB 2.2!
YaBB © 2000-2007. All Rights Reserved.