Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› Handlebar Control Wiring
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages: 1
Handlebar Control Wiring (Read 62 times)
JBK
Full Member
Offline
Posts: 100
MS
Gender:
Handlebar Control Wiring
09/10/21 at 19:11:15
Got new 1" HANDLEBAR and naturally needed 1" controls. I need the wiring diagram for the original. So I can connect what needs to connect without blowing anything up. Also for the horn, all signals.
Back to top
s-l1600_1.jpg
IP Logged
verslagen1
YaBB Moderator
ModSquad
Offline
Where there's a
will, I want to be
in it.
Posts: 28890
L.A. California
Gender:
Re: Handlebar Control Wiring
Reply #1 -
09/10/21 at 20:48:38
If anybody is going to help you out... they'll need to know what year and what side.
Back to top
Versey's Place
Tech Section Index
IP Logged
JBK
Full Member
Offline
Posts: 100
MS
Gender:
Re: Handlebar Control Wiring
Reply #2 -
09/12/21 at 12:16:20
You are right. 2001 needing both side.
Back to top
IP Logged
Madgrinders
YaBB Newbies
Offline
One point of view.
Posts: 44
East Los Angeles, California
Gender:
Re: Handlebar Control Wiring
Reply #3 -
09/12/21 at 12:54:11
JBK:
The controller you have pictured has separate turn signal controls, LEFT TURN on LEFT and RIGHT TURN on RIGHT? (Harley style) not BOTH DIRECTIONS on Left side like stock?
Back to top
IP Logged
JBK
Full Member
Offline
Posts: 100
MS
Gender:
Re: Handlebar Control Wiring
Reply #4 -
09/12/21 at 13:20:29
correct. they are sepeate. So just means I will have to run the original to the appropriate controls huh?
Back to top
IP Logged
Madgrinders
YaBB Newbies
Offline
One point of view.
Posts: 44
East Los Angeles, California
Gender:
Re: Handlebar Control Wiring
Reply #5 -
09/12/21 at 13:54:35
Hope this helps, (Total amateur here), but I think the left control should have 10 wires? (2 clutch safety, 3 turn signals, 3 hi/low, 2 horn). I would guess you would need to get the 3 wires for the turn signals and get the a common ground and right directional wire (light green) over to the right side controller.
Back to top
IP Logged
Dave
YaBB Moderator
ModSquad
Offline
SuzukiSavage.com
Rocks!
Posts: 18115
Camp Springs, Kentucky
Gender:
Re: Handlebar Control Wiring
Reply #6 -
09/13/21 at 03:50:36
I rewired my controls to allow me to use smaller 7/8" ones and lose the cruiser look. It was a significant job - I cut the wires and used the OEM wire connectors by just splicing the old and new wires together.
I use a KLR650 right control and a GSXR1000 left control......by sticking with the Suzuki left control I has some hope the wiring would be similar and thankfully it was.
I am not sure your new control has a "push to pass" switch that flashes the headlight - your old circuit will have two yellow wires and one is for the normal high beam and one is for the pass button.....you may not need them both. You will also have to reroute your right turn signal wire over to the other side.
The wiring harness is in the back of the Clymers Manual or in the Technical Section on this forum. I laid out the wires and used small pieces of tape to label each end, then began splicing them together being sure the length was proper for the handlebars I was using.
Good Luck - this is a challenging job.
http://suzukisavage.com/cgi-bin/YaBB.pl?num=1294779818
Back to top
Someday I will be old......But not today!
IP Logged
Pages: 1
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
10/06/24 at 01:21:01
›
General Category
›
Rubber Side Down!
› Handlebar Control Wiring
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.