SuzukiSavage.com - bar clamp and riser setup

Welcome, Guest. Please Login or Register :: View Members

SuzukiSavage.com › General Category › Rubber Side Down! › bar clamp and riser setup

(Moderators: verslagen1, Dave, Serowbot)

‹ Previous topic | Next topic ›

Pages: 1 2

bar clamp and riser setup (Read 263 times)

norm92de Serious Thumper Offline SuzukiSavage.com Rocks! Posts: 1180 El Paso TX Gender:	Re: bar clamp and riser setup Reply #15 - 08/15/16 at 11:04:54 Tocsic, The length of the risers could be a bit less but 3" works out fine with the stock controls without any problems, which might be the case if you make them much shorter. Versy ought to put out a kit ready to go. No chasing around for bolts etc.
Back to top	2014 S40. Raptor. idle mixture adj.Needle raised one notch. 4000' altitude. Stock jets. Shell Rotella synthetic. IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28886 L.A. California Gender:	Re: bar clamp and riser setup Reply #16 - 08/15/16 at 11:50:51 Hey Norm, I didn't tell you, but I just sprayed those with WD-40 to prevent corrosion durring shipping. You should at least wax them.
Back to top	Versey's Place Tech Section Index IP Logged

norm92de Serious Thumper Offline SuzukiSavage.com Rocks! Posts: 1180 El Paso TX Gender:	Re: bar clamp and riser setup Reply #17 - 08/15/16 at 12:19:08 In El Paso corrosion is not on the cards.
Back to top	2014 S40. Raptor. idle mixture adj.Needle raised one notch. 4000' altitude. Stock jets. Shell Rotella synthetic. IP Logged

zipidachimp Serious Thumper Online SuzukiSavage.com Rocks! Posts: 1417 surrey, b.c. Gender:	Re: bar clamp and riser setup Reply #18 - 08/15/16 at 21:43:46 local fastenal is great for 200 at a time. no singles!
Back to top	IP Logged

Dave

YaBB Moderator
ModSquad

Offline

SuzukiSavage.com
Rocks!

Posts: 18099
Camp Springs, Kentucky
Gender: male

Re: bar clamp and riser setup
Reply #19 - 08/16/16 at 04:37:14

zipidachimp wrote on 08/15/16 at 21:43:46:

local fastenal is great for 200 at a time. no singles! Angry

My local Fastenal is the same....the fasteners in stock are all in bags of 50 or more.

If you want smaller quantities they can order them and have them in a couple days - but.....they charge you shipping! I found it is actually cheaper, faster and more reliable to just go online to Fastenal and order the stuff online, and have it shipped to you. (The stainless allen screw carb sets I put together all came from Fastenal).

Someday I will be old......But not today!

IP Logged

norm92de

Serious Thumper

Offline

SuzukiSavage.com
Rocks!

Posts: 1180
El Paso TX
Gender: male

Re: bar clamp and riser setup
Reply #20 - 08/30/16 at 12:00:02

FWIW,
I fitted a pair of 3" risers that Verslagen made for me. 'Temporarily' I used 6" 3/8 x16 bolts, 94 cents nuts and all, from Tractor Supply probably made of regurgitated toffee. Anyway, I haven't got around to fitting metric socket head bolts yet and I don't think I will. The cheapos' seem to be doing everything one needs. The local store wanted about $5.00 apiece for the metric article! Hex-head wasn't problem with tightening as I expected, they just torqued down normally.-sorry Cheapnewby- Shocked

2014 S40. Raptor. idle mixture adj.Needle raised one notch. 4000' altitude. Stock jets. Shell Rotella synthetic.

IP Logged

ohiomoto Serious Thumper Offline SuzukiSavage.com Rocks! Posts: 2772	Re: bar clamp and riser setup Reply #21 - 08/30/16 at 17:50:27 Don't be afraid to try Ace Hardware. There is one near my office that stocks a really nice selection of fasteners and metals.
Back to top	IP Logged

Pages: 1 2

‹ Previous topic | Next topic ›

« Home