Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› Re-jetting after Harley Muffler install
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages:
1
2
3
...
5
Re-jetting after Harley Muffler install (Read 504 times)
hawk41
Junior Member
Offline
SuzukiSavage.com
Rocks!
Posts: 65
Gilbert, AZ
Gender:
Re-jetting after Harley Muffler install
07/06/16 at 10:38:17
Before I try to change the jets after my recent Harley muffler install I would like to know how many turns out on the idle mixture screw is stock. At 1.5 turns to 2.5 turns I really can't tell much difference in the idle, however, when riding there seems to be more backfires at 1.5 than at 2.5. Suggestions would be appreciated.
Back to top
Older than dirt but still kickin' up dust!
IP Logged
Dave
YaBB Moderator
ModSquad
Offline
SuzukiSavage.com
Rocks!
Posts: 18099
Camp Springs, Kentucky
Gender:
Re: Re-jetting after Harley Muffler install
Reply #1 -
07/06/16 at 11:58:56
In order to properly set the idle mixture screw, you may need to turn the idle speed down a little bit....down to around 800 rpm. This is lower than recommended for a healthy cam (low oil pressure at low idle speeds) - but at 1,000 - 1,100 rpm some fuel begins to flow out of the needle jet and makes adjusting the idle fuel mixture impossible. Start at 1.5 turns out and then adjust. If you can turn the screw all the way in without the engine dying - the pilot jet is too big.....and if you have to turn the screw out more than 2.5 turns the idle jet is too small. Don't let the engine lean over on the side stand while you are making the adjustment....hold the bike upright so the cam is oiled properly. Then turn the idle speed back up when you are done. And you can open the mixture screw up a 1/8th turn or so extra to help reduce the backfire - but you really should be jetting for a bike that runs properly when the throttle is open, and ignore what it does when the throttle is closed.
https://www.youtube.com/watch?v=YxpQjDQzX7g
https://www.youtube.com/watch?v=zm5mB3R8Ucw
Back to top
Someday I will be old......But not today!
IP Logged
hawk41
Junior Member
Offline
SuzukiSavage.com
Rocks!
Posts: 65
Gilbert, AZ
Gender:
Re: Re-jetting after Harley Muffler install
Reply #2 -
07/06/16 at 12:42:31
Thanks for the info! Results are as follows:
1.5 turns - backfires a lot while throttling up
.75 turns - engine dies
2.5 turns - While underway, rolling the throttle off gently to shift, pretty loud backfire almost every shift.
Does this indicate the idle jet is too small? How many sizes up should I go or is that just trail & error.
Is this a typical change when you go to a Harley muffler? Thanks!
Back to top
Older than dirt but still kickin' up dust!
IP Logged
verslagen1
YaBB Moderator
ModSquad
Offline
Where there's a
will, I want to be
in it.
Posts: 28886
L.A. California
Gender:
Re: Re-jetting after Harley Muffler install
Reply #3 -
07/06/16 at 13:08:22
hawk41 wrote
on 07/06/16 at 12:42:31:
2.5 turns - While underway, rolling the throttle off gently to shift, pretty loud backfire almost every shift.
You need to double check for exhaust leak.
Also, does the HD muff have the straight thru baffle intact?
After you're sure about these Q's, then I'd up size the pilot.
Back to top
Versey's Place
Tech Section Index
IP Logged
hawk41
Junior Member
Offline
SuzukiSavage.com
Rocks!
Posts: 65
Gilbert, AZ
Gender:
Re: Re-jetting after Harley Muffler install
Reply #4 -
07/06/16 at 13:14:09
New exhaust gasket and torqued to specs.
Bought the HD muffler here on SuzukiSavage.com and it has the straight thru baffle.
When sizing up, should I purchase several diff. sizes and experiment?
Thanks!
Back to top
Older than dirt but still kickin' up dust!
IP Logged
Kris01
Serious Thumper
Offline
Eat, sleep, RIDE!
Posts: 3767
Tennessee
Gender:
Re: Re-jetting after Harley Muffler install
Reply #5 -
07/06/16 at 16:57:16
What jets are you currently using?
Back to top
There's no problem that a full tank of gas and a sunny day can't fix!
2008 S40, Rotella T 15W-40 w/ZDDP added, Dyna, 140/90-15, Battery Tender Jr., Seat lift, #52.5/150/3 washers, Raptor
IP Logged
hawk41
Junior Member
Offline
SuzukiSavage.com
Rocks!
Posts: 65
Gilbert, AZ
Gender:
Re: Re-jetting after Harley Muffler install
Reply #6 -
07/06/16 at 17:04:00
Don't know yet! Have to study how to remove it! Am I correct in assuming there is only one pilot jet. I am sure there are instructions here on SuzukiSavage.com on the procedure for removal. Just need to find the correct thread. I will post the jet size once I get my hands on it.
Back to top
Older than dirt but still kickin' up dust!
IP Logged
Kris01
Serious Thumper
Offline
Eat, sleep, RIDE!
Posts: 3767
Tennessee
Gender:
Re: Re-jetting after Harley Muffler install
Reply #7 -
07/06/16 at 17:12:40
Yes, 1 pilot jet, 1 main jet. You'll also want to shim the jet needle. It controls about 1/4-3/4 throttle. That's where you'll spend most of your time.
http://suzukisavage.com/cgi-bin/YaBB.pl?board=tech;action=display;num=1098869040
http://suzukisavage.com/cgi-bin/YaBB.pl?board=tech;action=display;num=1157720585
http://suzukisavage.com/cgi-bin/YaBB.pl?num=1309246277
http://suzukisavage.com/cgi-bin/YaBB.pl?num=1221818822/0#0
http://suzukisavage.com/cgi-bin/YaBB.pl?num=1350749896/0
Back to top
There's no problem that a full tank of gas and a sunny day can't fix!
2008 S40, Rotella T 15W-40 w/ZDDP added, Dyna, 140/90-15, Battery Tender Jr., Seat lift, #52.5/150/3 washers, Raptor
IP Logged
hawk41
Junior Member
Offline
SuzukiSavage.com
Rocks!
Posts: 65
Gilbert, AZ
Gender:
Re: Re-jetting after Harley Muffler install
Reply #8 -
07/06/16 at 18:45:48
Thanks! Is there a particular size of shim that I need to buy? It does sound from reading the links that you provided that I probably just need to get the next jet size up. It will be interesting to see if the previous owner has changed the factory jet as the plug over the idle screw had already been removed. Just need to find out how to remove the pilot jet and shim the jet needle!
Back to top
Older than dirt but still kickin' up dust!
IP Logged
Kris01
Serious Thumper
Offline
Eat, sleep, RIDE!
Posts: 3767
Tennessee
Gender:
Re: Re-jetting after Harley Muffler install
Reply #9 -
07/06/16 at 20:07:11
3 #4 brass washers
should
do the trick! That's about 2/3 the thickness of the original nylon shim. You can find these washers at larger home improvement stores (Home Depot, Lowes, etc) or you can contact Lancer. He sells a kit that has everything you need.
The original owner of mine had drilled out the pilot screw plug but it still had the stock jets.
Lancer's jet kit:
http://suzukisavage.com/cgi-bin/YaBB.pl?num=1336741909
Back to top
There's no problem that a full tank of gas and a sunny day can't fix!
2008 S40, Rotella T 15W-40 w/ZDDP added, Dyna, 140/90-15, Battery Tender Jr., Seat lift, #52.5/150/3 washers, Raptor
IP Logged
zipidachimp
Serious Thumper
Offline
SuzukiSavage.com
Rocks!
Posts: 1416
surrey, b.c.
Gender:
Re: Re-jetting after Harley Muffler install
Reply #10 -
07/06/16 at 23:02:32
At sea level, Dyna muff, white spacer 1/2 thickness, pilot 55, main 155, my bike has become a rocket, 95% no backfires! Woohoo!
Back to top
IP Logged
hawk41
Junior Member
Offline
SuzukiSavage.com
Rocks!
Posts: 65
Gilbert, AZ
Gender:
Re: Re-jetting after Harley Muffler install
Reply #11 -
07/06/16 at 23:11:10
Nothing about carbs makes sense to me (sh*t, life doesn't make sense to me but what else is new)! So! Are you saying that the shim needs to be "less" in size than the original. "Shims" are supposed to be make something bigger,right? I think it's time for another Gin & tonic!
Back to top
Older than dirt but still kickin' up dust!
IP Logged
Dave
YaBB Moderator
ModSquad
Offline
SuzukiSavage.com
Rocks!
Posts: 18099
Camp Springs, Kentucky
Gender:
Re: Re-jetting after Harley Muffler install
Reply #12 -
07/07/16 at 03:52:09
hawk41 wrote
on 07/06/16 at 13:14:09:
Bought the HD muffler here on SuzukiSavage.com and it has the straight thru baffle.
Does that mean you can see straight through the muffler....if you look into one end can you see daylight coming from the other end?
Back to top
Someday I will be old......But not today!
IP Logged
hawk41
Junior Member
Offline
SuzukiSavage.com
Rocks!
Posts: 65
Gilbert, AZ
Gender:
Re: Re-jetting after Harley Muffler install
Reply #13 -
07/07/16 at 06:32:00
Yep! Can see straight thru. How do I get access to the pilot jet, etc.? Do I have to remove the carb or can I do it on the bike?
Back to top
Older than dirt but still kickin' up dust!
IP Logged
Dave
YaBB Moderator
ModSquad
Offline
SuzukiSavage.com
Rocks!
Posts: 18099
Camp Springs, Kentucky
Gender:
Re: Re-jetting after Harley Muffler install
Reply #14 -
07/07/16 at 06:53:56
hawk41 wrote
on 07/07/16 at 06:32:00:
Yep! Can see straight thru. How do I get access to the pilot jet, etc.? Do I have to remove the carb or can I do it on the bike?
Well....that is part of your problem. Somebody has knocked the little plate out of the baffle - you should not be able to see straight through the muffler. Halfway down the muffler there is supposed to be a little metal plug - it forces the exhaust to go out the holes into the outer shell, then on the backside of the plug the exhaust comes out of the outer shell and back into the center pipe.....the out the back. Without that plug in the center you don't have a "muffler"....you have a "straight pipe" or "drag pipe". You will never be able to jet your carb to stop the backfiring and noise when the exhaust just goes through a straight pipe.
Back to top
Someday I will be old......But not today!
IP Logged
Pages:
1
2
3
...
5
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
09/28/24 at 08:30:17
›
General Category
›
Rubber Side Down!
› Re-jetting after Harley Muffler install
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.