Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› Ryca Project - question about the tank/seat mount
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages: 1
Ryca Project - question about the tank/seat mount (Read 90 times)
thomasoconnor19
Full Member
Offline
SuzukiSavage.com
Rocks!
Posts: 147
Ryca Project - question about the tank/seat mount
04/15/13 at 15:41:20
This is my Ryca bike I have been working on. Instead of using their tank, I have used a Suzuki GT550 tank that fit very easily.
One problem I've ran into is that the tank is a a good inch longer and it doesn't leave me with enough room to get the nuts on the bolts that assemble the tank and seat pan.
Can I drill out the nuts on the frame, and drop the bolt down through the holes instead? Just wondering if this effects the ability of everything being held together?
I also am planning to chop off a bit of the front of the fiberglass seat as well as reshape the upholstery to fit flush with the tank.
Back to top
IP Logged
Dave
YaBB Moderator
ModSquad
Offline
SuzukiSavage.com
Rocks!
Posts: 18098
Camp Springs, Kentucky
Gender:
Re: Ryca Project - question about the tank/seat mo
Reply #1 -
04/15/13 at 18:19:45
I am using the same tank as you - but I lowered and pushed my tank more forward than you have. It was a lot of work getting the tank to sit lower.
If you are using the RYCA battery box mount - you need to see if you have access to put nuts on the bottom if you decide to put the bolts in from the top.
Here is the link to my build and you can see how I mounted my tank.
http://suzukisavage.com/cgi-bin/YaBB.pl?num=1358099938
Dave
Back to top
Someday I will be old......But not today!
IP Logged
thomasoconnor19
Full Member
Offline
SuzukiSavage.com
Rocks!
Posts: 147
Re: Ryca Project - question about the tank/seat mo
Reply #2 -
04/18/13 at 08:43:31
Looks good Dave. Last night I realized I could have dropped the front of my tank a little bit more - but I am just going to keep it as is. I plan to notch my swingarm and add a larger rear tire so I think it will level my bike out a little more.
Did you use the GT550 petcock on your Savage? I'm assuming it will work?
Back to top
IP Logged
thomasoconnor19
Full Member
Offline
SuzukiSavage.com
Rocks!
Posts: 147
Re: Ryca Project - question about the tank/seat mo
Reply #3 -
04/18/13 at 08:45:59
I noticed in your build that you had to move your petcock mounts. With the GT550 tank mounted where I put it - the petcock clears my cylinder. Even if I drop the front a ~1/2" or so, it still clears.
Back to top
IP Logged
Pages: 1
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
09/25/24 at 08:25:51
›
General Category
›
Rubber Side Down!
› Ryca Project - question about the tank/seat mount
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.