SuzukiSavage.com - button/pan head bolts for rear fender (Oldfeller)

Welcome, Guest. Please Login or Register :: View Members

SuzukiSavage.com › General Category › Rubber Side Down! › button/pan head bolts for rear fender (Oldfeller)

(Moderators: verslagen1, Dave, Serowbot)

‹ Previous topic | Next topic ›

Pages: 1

button/pan head bolts for rear fender (Oldfeller) (Read 49 times)

DrunkenDwarf

Senior Member

Offline

Morning Zombie

Posts: 325
Seattle, WA
Gender: male

button/pan head bolts for rear fender (Oldfeller)
10/12/12 at 11:59:25

I'm putting a slightly larger tire on (Pirelli MT66 140/90H-15) so I went looking for the thread about bolt replacement and found this one by Oldfeller:
http://suzukisavage.com/cgi-bin/YaBB.pl?num=1181496112/1#1

So I removed a couple of bolts to verify his quantity and dimensions.

1) Item #C - I seem to have only two of these. The other two appear to be pegs from the turn signals.
2) Item #B - These are 45mm, not 35mm
3) Item #A - These appear to be loctited in. After my last experience (broken bolts) I'm a little gun shy about replacing them. Are these replaceable easily?

Thanks.

-D. Dwarf

Pearl White 2007 S40; Dyna exhaust; Current jets: 52.5 w/ bleed (2 turns out) / 1.5mm (0.06") spacer / 150; raptor petcock

IP Logged

youzguyz

Serious Thumper

Offline

Posts: 2538
San Antonio, Texas
Gender: male

Re: button/pan head bolts for rear fender (Oldfell
Reply #1 - 10/12/12 at 12:56:57

OF's post is for a MUCH larger rear tire.
The 140/90-15 is only a little larger.
If you have saddle bag brackets, then you would want to change out the "B" bolts, at least on the right side.
Other wise, should not be a problem.

If you want to make sure.. put the tire on, jack the bike up, take off the rear shocks. Put chalk on the bolt heads. Push the tire up into the fender and see if it rubs anywhere on the bolts.

2002 - Silver (Thumper)
2000 - Green (Mad Hamish)
Most motorcycle problems are caused by the nut between the seat and the handlebars. Make sure yours isn't too tight or too loose.

IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28890 L.A. California Gender:	Re: button/pan head bolts for rear fender (Oldfell Reply #2 - 10/12/12 at 13:37:35 Don't worry about A's, they don't come in contact with the tire. Only B's and C's on the side rails. And yeah, I only have 2 as well.
Back to top	Versey's Place Tech Section Index IP Logged

DrunkenDwarf Senior Member Offline Morning Zombie Posts: 325 Seattle, WA Gender:	Re: button/pan head bolts for rear fender (Oldfell Reply #3 - 10/12/12 at 16:03:16 Good. I'll re-loctite the one I got loose to measure and pretend I didn't touch the others. Thanks. -D. Dwarf
Back to top	Pearl White 2007 S40; Dyna exhaust; Current jets: 52.5 w/ bleed (2 turns out) / 1.5mm (0.06") spacer / 150; raptor petcock IP Logged

Pages: 1

‹ Previous topic | Next topic ›

« Home