Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› Belt hitting engine bolt RYCA. more pics posted
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages:
1
2
Belt hitting engine bolt RYCA. more pics posted (Read 267 times)
sbaugz
Ex Member
Re: Belt hitting engine bolt RYCA. more pics poste
Reply #15 -
06/14/11 at 10:35:17
thumperclone wrote
on 06/14/11 at 09:27:33:
sure the spacer is behind the pulley
Hmm, been a few weeks since I put the pulley back on. Cannot recall if there was a spacer involved in the re-install. Will have to check the Clymer again and possibly remove pulley to double check.
Back to top
IP Logged
ralfyguy
Serious Thumper
Offline
Posts: 932
Re: Belt hitting engine bolt RYCA. more pics poste
Reply #16 -
06/14/11 at 10:35:31
thumperclone wrote
on 06/14/11 at 09:27:33:
sure the spacer is behind the pulley
Looks like the spacer is missing to me. That or the wrong one.
Back to top
IP Logged
sbaugz
Ex Member
Re: Belt hitting engine bolt RYCA. more pics poste
Reply #17 -
06/14/11 at 10:38:22
ralfyguy wrote
on 06/14/11 at 10:35:31:
thumperclone wrote
on 06/14/11 at 09:27:33:
sure the spacer is behind the pulley
Looks like the spacer is missing to me. That or the wrong one.
\Thanks, I will check it out. Dangit, and here I thought I was done wrestling with that stupid pulley nut.
Back to top
IP Logged
MotoBuddha
Serious Thumper
Offline
Let's roll!
Posts: 1416
Charlotte, NC
Re: Belt hitting engine bolt RYCA. more pics poste
Reply #18 -
06/14/11 at 10:41:06
If the spacer is missing, then the belt will want to track even tighter to the inside edge of the front pulley (because you're moving the pulley outward). That makes checking the axle position that much more necessary.
Back to top
Travel kills ignorance.
IP Logged
sbaugz
Ex Member
Re: Belt hitting engine bolt RYCA. more pics poste
Reply #19 -
06/14/11 at 19:18:59
MotoBuddha wrote
on 06/14/11 at 10:41:06:
If the spacer is missing, then the belt will want to track even tighter to the inside edge of the front pulley (because you're moving the pulley outward). That makes checking the axle position that much more necessary.
There really isn't a spacer. The posts and comment here had me worried that I missed a little washer or something. I took mine apart and didn't see one. I then looked at the microfiche at ronayers.com and didn't see one listed there either. Yes, there is a spacer, but its about an inch wide and that is definately installed on mine.
Looks like I had it (drive pulley) mounted correctly after all. RYCA took a look at my photos and commented that the belt is too loose, so I will tighten that up and see how it looks. Hopefully the bolt mentioned earlier will clear if I tighten up the belt.
Back to top
IP Logged
MotoBuddha
Serious Thumper
Offline
Let's roll!
Posts: 1416
Charlotte, NC
Re: Belt hitting engine bolt RYCA. more pics poste
Reply #20 -
06/14/11 at 19:51:48
sbaugz wrote
on 06/14/11 at 19:18:59:
RYCA took a look at my photos and commented that the belt is too loose, so I will tighten that up and see how it looks. Hopefully the bolt mentioned earlier will clear if I tighten up the belt.
Like my dad used to say, eliminate the simple things first.
Back to top
Travel kills ignorance.
IP Logged
Pages:
1
2
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
09/23/24 at 22:14:27
›
General Category
›
Rubber Side Down!
› Belt hitting engine bolt RYCA. more pics posted
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.