Donate!
Welcome, Guest. Please Login or Register :: View Members
Pages: 1
Send Topic Print
Clutch Cover "form-a-gasket" technique (Read 1615 times)
Oldfeller--FSO
Serious Thumper
ModSquad
*****
Offline

Hobby is now
"concentrated
neuropany"

Posts: 12629
Fayetteville, NC
Gender: male
Clutch Cover "form-a-gasket" technique
11/02/09 at 07:16:36
 
 
A compression gasket requires an even application of a known torque value range to work correctly.  Over torque crushes and ruins the gasket and warps the cover.  Undertorque is just less clamping force but it does not damage the gasket nor warp the cover.

Long time ago I bought me a little quarter inch drive "inch pound" torque wrench for compression gasket use.

Default values for me if there are no known torque values for the involved gasket screws/bolts is 80-100 inch pounds with stress being put on a multi-level cross pattern pull up and consistency on final torque.  This I got from oil pans on car engines -- the touchiest compression gaskets in the world for leaking over time.

I think our side cover gaskets DO have a spec at 6.5 - 9.5 foot pounds (given for 6mm crankcase fasteners) which translates to 78 to 114 inch pounds.  Them, I'd shoot for 100 inch pounds on the nose with a good 3 level repeat cross pattern with first level at 50, second at 80 and last round at 100 inch pounds.  This ought to do her jest fine.

Gasket torque wrenches cost $30 to $50 most places as they are somewhat "specialty tools" and are not big volume items by anybody's guesstimation.  Shame that, every bike mechanic really needs one.



==========   Ta Da !!!  ==========   Jedi science comes up with an answer !!



Now, for the budget minded amongst us Harbor Freight has the no-brainer 6 newton/meter (or 72 inch pound) install a gasket tool for your Savage engine for a whopping $3.97 price tag.  Can't get more reasonable than this.  

Yoda approved as it hits right close at the bottom end of the Suzuki/Clymer recommended gasket installation torque values.

(less a half a newton/meter off and the other torque wrenches don't even graduate that fine)  

That's six inch pounds shy to you English speakers.

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=66269



Back to top
 
« Last Edit: 12/08/12 at 12:54:24 by Oldfeller--FSO »  

Former Savage Owner
  IP Logged
Oldfeller--FSO
Serious Thumper
ModSquad
*****
Offline

Hobby is now
"concentrated
neuropany"

Posts: 12629
Fayetteville, NC
Gender: male
Re: Clutch Sidecover gasket (make your own)
Reply #1 - 12/29/10 at 16:54:03
 

I mentioned earlier that the black gasket stuff keeps getting better and better.

It is now good enough not to require a paper gasket of any kind.  Just coat both surfaces then assemble the cover and finger tighten the screws very lightly until the squeezing oozing action just barely starts.  Stop there on purpose and wait 24 hours .....

You are permitting a good boundary layer to form and to remain in place between the two housings to become "the gasket".

Then after you wait 24 hours then you apply the required torque and wait an hour or two then retorque only once.

Wink

Well, hells bells boys -- it is even cheaper and easier than a paper gasket and the stuff is good enough now for it to work reliably by itself.
Back to top
 
« Last Edit: 01/03/11 at 07:38:28 by Oldfeller--FSO »  

Former Savage Owner
  IP Logged
youzguyz
Serious Thumper
*****
Offline



Posts: 2509
San Antonio, Texas
Gender: male
Re: Clutch Sidecover gasket (make your own)
Reply #2 - 01/03/11 at 07:28:09
 
OF.  What kind of "black gasket stuff" are you speaking of?
Permatex Ultra Black?

http://www.permatex.com/products/Automotive/automotive_gasketing/gasket_maker...

Something else?

Back to top
 
 

2002 - Silver (Thumper)
2000 - Green (Mad Hamish)
Most motorcycle problems are caused by the nut between the seat and the handlebars. Make sure yours isn't too tight or too loose.
  IP Logged
Oldfeller--FSO
Serious Thumper
ModSquad
*****
Offline

Hobby is now
"concentrated
neuropany"

Posts: 12629
Fayetteville, NC
Gender: male
Re: Clutch Sidecover gasket (make your own)
Reply #3 - 01/03/11 at 07:36:53
 



Yup, that's the black stuff -- they make the same stuff in a silver stuff too for those with older unpainted motors.

The stuff is now "safe for sensors" too, which is another improvement.
Back to top
 
 

Former Savage Owner
  IP Logged
Gyrobob
Serious Thumper
*****
Offline

Posers ain't
motorcyclists

Posts: 2571
Newnan, GA
Gender: male
Re: Clutch Sidecover gasket (make your own)
Reply #4 - 05/07/11 at 10:19:18
 
motobuddha said "I know people who coat at least one side of their gaskets with ChapStick so it will release cleanly when they need to remove the cover. They swear they've had no problems, but I don't do it myself. "

I've used a trick sorta like this for decades to replace gaskets with RTV.

-- Clean both surfaces well.  

-- Coat one surface with a very thin layer of grease.  

-- I learned the hard way about using a a silicone-based grease -- don't do it. I use wheel bearing grease or some such.  

-- Put a thin layer of RTV on one surface, coating only the outer 2/3 of the surface (you don't want a gob of sealant squeezed inside the joint).  

-- Let it skin over -- takes maybe 10-15 minutes.  

-- Gently join the surfaces, and tighten the fasteners evenly about 90% of the way.  

-- Wait another 30 minutes, then tighten the rest of the way.

I love this technique because it never leaks, and if done correctly, you can pop the joint apart over and over again, and never have to reseal it.  Cheap, too.  In effect, it creates a permanent RTV gasket glued to one side of the joint.

Back to top
 
 

If you think there's good in everyone, you haven't met everyone.
  IP Logged
Gyrobob
Serious Thumper
*****
Offline

Posers ain't
motorcyclists

Posts: 2571
Newnan, GA
Gender: male
Re: Clutch Sidecover gasket (make your own)
Reply #5 - 05/07/11 at 10:21:34
 
Do any of the clutch cover bolts need any washers?  (metal or otherwise?)
Back to top
 
 

If you think there's good in everyone, you haven't met everyone.
  IP Logged
verslagen1
YaBB Moderator
ModSquad
*****
Offline

Where there's a
will, I want to be
in it.

Posts: 28733
L.A. California
Gender: male
Re: Clutch Sidecover gasket (make your own)
Reply #6 - 05/07/11 at 11:09:55
 
Gyrobob wrote on 05/07/11 at 10:21:34:
Do any of the clutch cover bolts need any washers?  (metal or otherwise?)


Yes 3 do, see cam chain adjuster check procedure.
Back to top
 
 
WWW   IP Logged
Oldfeller--FSO
Serious Thumper
ModSquad
*****
Offline

Hobby is now
"concentrated
neuropany"

Posts: 12629
Fayetteville, NC
Gender: male
Re: Clutch Sidecover gasket (make your own)
Reply #7 - 05/07/11 at 14:34:45
 


Specifically, these 3 need a rubber backed washer.


Back to top
 
 

Former Savage Owner
  IP Logged
Gyrobob
Serious Thumper
*****
Offline

Posers ain't
motorcyclists

Posts: 2571
Newnan, GA
Gender: male
Re: Clutch Sidecover gasket (make your own)
Reply #8 - 05/07/11 at 19:45:18
 
Excellent.  Now, I am wondering why these three need a rubber-backed washer.
Back to top
 
 

If you think there's good in everyone, you haven't met everyone.
  IP Logged
verslagen1
YaBB Moderator
ModSquad
*****
Offline

Where there's a
will, I want to be
in it.

Posts: 28733
L.A. California
Gender: male
Re: Clutch Sidecover gasket (make your own)
Reply #9 - 05/07/11 at 20:29:15
 
oil passage running behind them.
Back to top
 
 
WWW   IP Logged
Oldfeller--FSO
Serious Thumper
ModSquad
*****
Offline

Hobby is now
"concentrated
neuropany"

Posts: 12629
Fayetteville, NC
Gender: male
Re: Clutch Sidecover gasket (make your own)
Reply #10 - 05/09/11 at 04:34:29
 

Speaking of oil passages, there is the biggie, the 50-60 psi at full rpm main oil channel that rides along the top edge of the cover that has to be clamped and sealed against full rpm oil pressure.

Be sure not to block off any of the two outlets with excess RTV ooze ....

...... and I'd forgo any chapstick tricks in this area (you need an absolute maximum adhesion seal on both sides of that 1/8" wide top rib)
Back to top
 
 

Former Savage Owner
  IP Logged
Pages: 1
Send Topic Print


« Home

 
« Home
SuzukiSavage.com
03/28/24 at 23:19:41



General CategoryTechnical Documents/Reference › Clutch Cover "form-a-gasket" technique


SuzukiSavage.com » Powered by YaBB 2.2!
YaBB © 2000-2007. All Rights Reserved.