SuzukiSavage.com - Needle jet clip?

Welcome, Guest. Please Login or Register :: View Members

SuzukiSavage.com › General Category › Rubber Side Down! › Needle jet clip?

(Moderators: verslagen1, Dave, Serowbot)

‹ Previous topic | Next topic ›

Pages: 1

Needle jet clip? (Read 77 times)

littlefights

Junior Member

Offline

SuzukiSavage.com
Rocks!

Posts: 54

Gender: male

Needle jet clip?
09/16/09 at 13:43:53

A couple of different people suggested moving the needle jet clip up one notch after installing a new muffler. I've got my carb off and disassembled and hell if I can't figure out a way to do anything with the needle jet clip, assuming I'm looking at the right thing. Can anyone point me in the right direction?

And quick - the dining room smells like gas and the wife is giving me the stink-eye.

IP Logged

Oldfeller--FSO Serious Thumper ModSquad Offline Hobby is now "concentrated neuropany" Posts: 12677 Fayetteville, NC Gender:	Re: Needle jet clip? Reply #1 - 09/16/09 at 13:48:47 Most of us don't have clips on our needle, nor do we have extra grooves on the needle for the non-existent clip to go into. Only the early Savages had grooved needles. Instead, we sand down our white spacer to remove half of it.
Back to top	Former Savage Owner IP Logged

serenity3743 Serious Thumper Offline Striving to better, oft we mar what's well Posts: 778 Black Mountain, NC Gender:	Re: Needle jet clip? Reply #2 - 09/16/09 at 13:49:46 Someone else will be more knowledgeable about this than I am, but I believe the stock carb has the "white spacer" instead of the clip. To adjust for a richer fuel mix, you file down the thickness of the white spacer or replace it with #3 washers.
Back to top	2000 LS650P Suzuki windshield, luggage rack, saddle bag racks, k & n air filter, Dyna muffler,2/3 white spacer, do-it-myself seat. Love to ride! IP Logged

prechermike Serious Thumper Alliance Member Offline Kalashna Kitty, from Skat Posts: 1190 Ponzer, NC Gender:	Re: Needle jet clip? Reply #3 - 09/16/09 at 13:52:46 And take the spacer with you to get the right size washers inside and outside diameter. Guess how I know!
Back to top	2006, HD pipe, Tkat fork brace, elkhide handgrips, gel seat w/riser, silverblue, Ed L's forward controls, Wristwatch, biblethumper650@gmail.com IP Logged

littlefights Junior Member Offline SuzukiSavage.com Rocks! Posts: 54 Gender:	Re: Needle jet clip? Reply #4 - 09/16/09 at 13:54:34 I've got an 86. There is a single groove with black c-clip in it. The previous owner did the white spacer mod - it looks like its been filed down to maybe 2mm. So I go up on the clip by reducing the white spacer? Should I trim it some more/replace it with a smaller one? Or just leave it out entirely? And thanks for the quick replies!
Back to top	IP Logged

matt Full Member Offline da na na na na mattman Posts: 228 Winter Springs, FL Gender:	Re: Needle jet clip? Reply #5 - 09/16/09 at 17:54:10 I have a needle jet like that (from the dynojet kit) and was advised to leave the white spacer in and use the clip for adjustments. I lowered the clip on mine (2 clicks = the width of the white spacer for me) it raises the needle up which is what removing the white spacer would do.
Back to top	IP Logged

jabman Senior Member Offline Posts: 411 England Gender:	Re: Needle jet clip? Reply #6 - 09/17/09 at 00:12:56 i believe matt is correct i have mine on the lowest needle with full spacer. if that is not enough throw the spacer and move the clip all the way up
Back to top	93" savage, 177.5 main, 52.5 w/holes 3 turns out , middle circlip, 6" k&n round filter, Dyna muffler, TKAT brace IP Logged

dasch Serious Thumper Offline SuzukiSavage.com Rocks! Posts: 1137	Re: Needle jet clip? Reply #7 - 09/17/09 at 01:44:47 same here, jabman
Back to top	IP Logged

Pages: 1

‹ Previous topic | Next topic ›

« Home