Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› Dont know where to go from here
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages:
1
2
3
Dont know where to go from here (Read 17 times)
klinc
Ex Member
Re: Dont know where to go from here
Reply #30 -
07/11/06 at 12:41:30
Kropatchek wrote
on 12/31/69 at 16:00:07:
Remember having seen this problem on the German forum.
Your frame and the CDI are from '87 and the engine is from '98 ; they don't match
Now you can do 2 things:
1) Remove the rotor from the 87 engine and install on the 98 engine - or
2) Get the CDI from the guy who sold you the 98 engine and install on yours.
Problem solved.
Greetz
Kropatchek 8)
Ah, My Uncle was just saying something about maybe the eloctronic timing is off. That he would doubt the mechanical timing was off with this few miles on it.
Thanks for the heads up and will see what I can come up with.
Edit: The person still has it and am going to to get it tonight. I wonder if this little endevour can get anymore expensive. I got this bike to save on gas and here I am driving all over Florida to grab parts everynight, lol.
I hope I am correct in that the CDI is the "Igniter"?
Back to top
IP Logged
klinc
Ex Member
Re: Dont know where to go from here
Reply #31 -
07/11/06 at 18:36:49
Well holy hell.......
Kropatchek, I owe you a drink it looks like.
Went and picked up the other computer and just put it on. I started up the bike and I can rev it up good now. I get the occasional backfire I am used to and I'm sure the carb will need adjusted a bit, but it feels much better now.
Just a note for others that may run into this problem. The connecters are different on these computers ("igniter" labeled box). Luckily the guy I got the parts from just handed me the whole wiring harness with everything left attached and just said take I dont need them. I was able to cut the two conenctors off and had to use some elec. tape to splice on the other connecter to fit the computer. I will fix it up better later. The wires were each colored differently and were extremly easy to splice right together. No diagram needed.
Everything seems to work while it is sitting there. I am going back out to put everything back together so I can ride it and check it out. Dear lord I am going on about 6 hours of sleep the last two days and if this thing runs I forsee yet another late night...... darn bike when its broke and darn bike when its running.
Hopefully this is it. Will keep you updated.
Thank you all for your help.
Back to top
IP Logged
klinc
Ex Member
Re: Dont know where to go from here
Reply #32 -
07/11/06 at 21:34:16
Well, I drove it home (about 30 minutes) and left the car at the office. Ran great all the way and not one backfire until I shut the bike down.
Thanks again all
Back to top
IP Logged
Kropatchek
Serious Thumper
Offline
Why more than 1
cylinder?
Posts: 1457
Alphen a/d Rijn Netherlands
Gender:
Re: Dont know where to go from here
Reply #33 -
07/12/06 at 02:09:53
You're welcome, glad to be of service.
Greetz
Kropatchek
Back to top
Never ask your bike to scream before her throat is warm.
'93 Sav in '96 ( yellow) looks
IP Logged
Pages:
1
2
3
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
09/23/24 at 04:22:13
›
General Category
›
Rubber Side Down!
› Dont know where to go from here
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.