Donate!
Welcome, Guest. Please Login or Register :: View Members
Pages: 1 ... 28 29 30 
Send Topic Print
Finn Hammer's Savage (Read 3425 times)
FinnHammer
Senior Member
****
Offline



Posts: 327
Denmark
Gender: male
Re: Finn Hammer's Savage
Reply #435 - 11/01/26 at 09:30:04
 
My endeavour into installing a stronger conrod has now been officially cancelled.
At first I thought that the JAWA speedway rod would be fine, but finding a suitable bearing proved challenging, to say the least. However the problem of accomodating the 23mm wristpin into the small end cancelled that possibility.
One last attempt included trying to have a custom rod manufactured by Carrillo. They will do it, and for a reasonable price actually. But a minimum order of 4.
Since I seem to be the only person on earth that has these concerns, I guess I have to forget about it, and rely on the experience of more seasoned riders, and accept the fact that the stock rod is strong enough.
Winter is coming close and the bike goes into storage. I will use some of the time to mount the 20deg. downdraught carburettor and the 35mm inlet valves. Bronze valve seats are already in my posession.

Cheers, Finn Hammer
Back to top
 
 

An expert is a person who has made all possible mistakes within a narrow field - Niels Bohr
WWW   IP Logged
Ruttly
Serious Thumper
*****
Offline

Thumpers Rule

Posts: 5619
Manteca , CA
Gender: male
Re: Finn Hammer's Savage
Reply #436 - 11/03/26 at 10:02:16
 
Your extremism is refreshing !  Cool
Back to top
 
 

The Topic Terminator
  IP Logged
DragBikeMike
Serious Thumper
*****
Offline

SuzukiSavage.com
Rocks!

Posts: 4767
Honolulu
Re: Finn Hammer's Savage
Reply #437 - 11/03/26 at 13:31:16
 
Very cool that you went through the trouble to look into the rod mod.  I really appreciate the photos of the disassembled crank.  I still think a long-rod engine would have distinct advantages over the standard rod, but I can also appreciate that you want to retain the special flat-top forged piston.  If I were to attempt the long-rod engine, I would probably use a Wiseco pop-top with the dome machined down to achieve reasonable compression ratio.  That way it would have the benefit of the forged piston.  Had you given any thought to how you would approach the balance issue, like possibly trying to have the rod manufactured such the finished rod would weigh the same as the stock rod, and possibly have the same weight distribution?  Do you think Carillo could do something like that?

Regarding the 35mm valves.  I fiddled around with those a bit and eventually concluded that the stock seats didn't have enough material to accommodate the larger valves.  But I have to admit that I never did an in-depth study of the situation.  I assume you have put more thought into the larger valves than I did.  Did you arrive at the same conclusion about the seats?  Do you think there is any chance that the stock seats could handle the larger valves?  I still would like to try the 35mm valves, but I don't feel that I have the skill required to replace the seats.  Did you lay the stock head out on CAD?
Back to top
 
 

Knowledge is power.
  IP Logged
FinnHammer
Senior Member
****
Offline



Posts: 327
Denmark
Gender: male
Re: Finn Hammer's Savage
Reply #438 - 11/04/26 at 14:46:05
 
Thankyou, Rutttly, I take that as a compliment.
As far as drawing the head in cad, this is what I have, and as a smart cookie over in one of the porting groups on Facebook said:"Spring seat saying: make my day" and of course that is where i will have my attention when I start to carve the inlet tract.
https://suzukisavage.com/yabb2.2/Attachments/inlet_port__20deg_001.JPG
The original seats are roughly 35mm, so there would not be much left of them, with an 88% throat. Therefore, I will fit 38mm valve seats.

That longer conrod is an intriguing option, and I wonder how much it would benefit, since there is not room for more than a few millimeters more than the stock item.
I was not too concerned about weight differences, considering that the poptop piston weighed quite a bit different than the stock one. I was thinking it would vibrate a bit more and probably at a slightly different RPM.
Carillo could match total weight within a few grams, and keep the ratio between big and small end correct too.
Cheers, Finn Hammer
Back to top
 
 

An expert is a person who has made all possible mistakes within a narrow field - Niels Bohr
WWW   IP Logged
zevenenergie
Serious Thumper
*****
Offline

SuzukiSavage.com
Rocks!

Posts: 2349
The Netherlands   Den Haag
Re: Finn Hammer's Savage
Reply #439 - Today at 14:07:35
 
I recently performed a calculation based on the "Einstein Gold" method from BainRacing. I had a subscription to the Gold edition, and it turns out the intake port on the Savage is actually too large; this negatively affects air velocity, which prevents optimal cylinder filling.

Making it even larger would require running at very high RPMs to justify such a large port.
On the other hand, the ratio between the intake and exhaust valves is nearly ideal at 86%; increasing the size of the intake valve would disrupt this balance.
I believe that if you reduce the taper of the intake—effectively making the entry smaller—while keeping the total length of the intake tract the same as the stock configuration, you would see better results.

Furthermore, the carburetor size should be selected so that it fits the gradually tapering intake duct, with the minimum cross-sectional area located at the valve seat.

I think more attention should be focused on optimizing the exhaust port—which, in my view, means building it up with weld material and reshaping it.

Your CAD drawing shows a much more ideal angle, but it would mean that the entire intake tract would have to incorporate a bend, and you really want it to be as straight as possible.

A different valve seat is required to achieve a proper 4-angle valve job, and in that case, 0.88% provides a good flow passage.
A different valve with a thicker valve head is required to incorporate a 15-degree angle, which serves as anti reversion.

So much for the insights I have gained recently through my theoretical study of tuning four-stroke engines.
Back to top
 
 

Funk emergencies are a serious matter and need to be dealt with immediately.
  IP Logged
Pages: 1 ... 28 29 30 
Send Topic Print


« Home

 
« Home
SuzukiSavage.com
11/22/26 at 15:26:34



› General Category › Rubber Side Down! › Finn Hammer's Savage


SuzukiSavage.com » Powered by YaBB 2.2!
YaBB © 2000-2007. All Rights Reserved.