SuzukiSavage.com - Hard start after new cam chain tensioner

ktec YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 3	Hard start after new cam chain tensioner 06/17/17 at 08:26:55 Hello, I have a 2001 Savage w/ raptor petcock at 8k miles. Installed the verslavy cam chain tensioner and ever since the bike is very hard to start. Before it would always start under 2 seconds, now it takes multiple tries and will shut off at idle until fully heated up. Any idea what's up and how to diagnose and fix?
Back to top	IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28886 L.A. California Gender:	Re: Hard start after new cam chain tensioner Reply #1 - 06/17/17 at 09:35:40 I would put a new sparkplug in and check the decomp adjustment.
Back to top	Versey's Place Tech Section Index IP Logged

Savageman Senior Member Offline Knowledge is half the battle Posts: 275 Marysville, California Gender:	Re: Hard start after new cam chain tensioner Reply #2 - 06/17/17 at 12:26:44 Sounds like the valve timing may have jumped a few teeth. Was the chain really loose when you installed the tensioner? Or you knocked loose some crap in the gas tank when installing the new petcock and right in the carb (pilot) jet.
Back to top	IP Logged

justin_o_guy2 Serious Thumper Offline What happened? Posts: 55279 East Texas, 1/2 dallas/la.	Re: Hard start after new cam chain tensioner Reply #3 - 06/17/17 at 12:55:45 How does it run?
Back to top	The people never give up their liberties but under some delusion.- Edmund Burke. IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28886 L.A. California Gender:	Re: Hard start after new cam chain tensioner Reply #4 - 06/17/17 at 13:00:04 Savageman wrote on 06/17/17 at 12:26:44: Sounds like the valve timing may have jumped a few teeth. Was the chain really loose when you installed the tensioner? I tried to get it to do that once, it would not with a half stretched chain. So, unless you had the cam chain off, I doubt that it's off timing.
Back to top	Versey's Place Tech Section Index IP Logged

Savageman Senior Member Offline Knowledge is half the battle Posts: 275 Marysville, California Gender:	Re: Hard start after new cam chain tensioner Reply #5 - 06/17/17 at 14:36:22 I've seen a very loose chain jump a few teeth, and it affects drivability. Usually affects idle range.
Back to top	IP Logged

justin_o_guy2 Serious Thumper Offline What happened? Posts: 55279 East Texas, 1/2 dallas/la.	Re: Hard start after new cam chain tensioner Reply #6 - 06/17/17 at 14:55:44 Timing can be checked without tearing it down.
Back to top	The people never give up their liberties but under some delusion.- Edmund Burke. IP Logged

ktec

YaBB Newbies

Offline

SuzukiSavage.com
Rocks!

Posts: 3

Re: Hard start after new cam chain tensioner
Reply #7 - 06/17/17 at 14:58:55

The bike runs good, feels like 10% low on power which could be 90+F heat we are getting in Joshua Tree, or memory is not accurate. Still, runs well hard to redline. IT HAS stopped backfiring as much and doesn't do the loud THUNDER BELCH after shutdown. Too bad, I liked it.

Also note that the starter does seem to be engaging as there is a whhirr and crank rotation. I hold over 5 seconds and no start. :'(
Petcock was installed years ago so not suspecting that.

I'll try new plug, also thinking the few weeks it sat waiting for tensioner fouled the carb.

Chain was a bit stretched, had to use the 2nd hole on verslavy and still it extended a couple mm out. I didn't notice and chain teeth slipping Lips Sealed

Back to top

IP Logged

justin_o_guy2 Serious Thumper Offline What happened? Posts: 55279 East Texas, 1/2 dallas/la.	Re: Hard start after new cam chain tensioner Reply #8 - 06/17/17 at 15:11:50 Piston at tdc. See if the valves are still evenly adjusted.
Back to top	The people never give up their liberties but under some delusion.- Edmund Burke. IP Logged

verslagen1

YaBB Moderator
ModSquad

Offline

Where there's a
will, I want to be
in it.

Posts: 28886
L.A. California
Gender: male

Re: Hard start after new cam chain tensioner
Reply #9 - 06/17/17 at 15:49:40

ktec wrote on 06/17/17 at 14:58:55:

The bike runs good, feels like 10% low on power which could be 90+F heat we are getting in Joshua Tree, or memory is not accurate. Still, runs well hard to redline. IT HAS stopped backfiring as much and doesn't do the loud THUNDER BELCH after shutdown. Too bad, I liked it.

Also note that the starter does seem to be engaging as there is a whhirr and crank rotation. I hold over 5 seconds and no start. :'(
Petcock was installed years ago so not suspecting that.

I'll try new plug, also thinking the few weeks it sat waiting for tensioner fouled the carb.

Chain was a bit stretched, had to use the 2nd hole on verslavy and still it extended a couple mm out. I didn't notice and chain teeth slipping Lips Sealed

If it runs past 50, then it's not a timing chain problem.
It'll run diffferently in the morn, temp affect the lean/rich setting.

Back to top

Versey's Place
Tech Section Index

IP Logged

jcstokes Serious Thumper Offline SuzukiSavage.com is very useful Posts: 2119 Mauku New Zealand Gender:	Re: Hard start after new cam chain tensioner Reply #10 - 06/17/17 at 16:58:03 Are you starting it with the throttle open or closed?
Back to top	Completely stock 2010 S40, aftermarket rev counter and back pack, Airhawk seat pad IP Logged

ktec YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 3	Re: Hard start after new cam chain tensioner Reply #11 - 06/17/17 at 18:15:09 jcstokes wrote on 06/17/17 at 16:58:03: Are you starting it with the throttle open or closed? I have to crack open the throttle now to get it started, not the case before.
Back to top	IP Logged

batman

Serious Thumper

Offline

SuzukiSavage.com
Rocks!

Posts: 3806
osceola new york
Gender: male

Re: Hard start after new cam chain tensioner
Reply #12 - 06/19/17 at 17:30:07

Chain was a bit stretched, had to use the 2nd hole on verslavy and still it extended a couple mm out. I didn't notice and chain teeth slipping Lips Sealed

[/quote]
A couple of mm out ?did the spring go hard? that sounds awful tight to me ,4-6mm would sound more normal to me ,maybe you switched to the second hole prematurely ,putting a lot of stress on the chain, and the cam bearings.You got the Vercy there is no danger going back to the first hole ,8,000 miles sounds early to need the second hole unless you've ridden it awfully hard.

Back to top

my old work mates called me MacGyver

IP Logged