Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› Piston ring end gap (free)
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages: 1
Piston ring end gap (free) (Read 121 times)
Mekh
Full Member
Offline
Suzuki Savage Rocks!
Posts: 128
Denmark
Gender:
Piston ring end gap (free)
01/13/17 at 08:45:14
Hi,
According to Clymers manual free end gap dimensions are:
Specification
Top 11.5mm
Second 14mm
Wear limit
Top 9.2mm
Second 11.2mm
Can someone please explain this to me? I do not understand why the wear limit distance is smaller than the specification distance.
I measure mine at about:
Top 11.5mm
Second 10.5mm
For information: gap distances inside the cylinder are just fine.
Back to top
IP Logged
youzguyz
Serious Thumper
Offline
Posts: 2538
San Antonio, Texas
Gender:
Re: Piston ring end gap (free)
Reply #1 -
01/13/17 at 13:35:05
The rings have to expand against the cylinder wall to seal it off.
If the free gap is too small, it doesn't have enough expansion force to provide an effective seal.
In My Opinion, if you have the engine apart enough to measure the free gap, then get the cylinder checked by a machine shop.
Get it honed, and replace the rings.
Back to top
2002 - Silver (Thumper)
2000 - Green (Mad Hamish)
Most motorcycle problems are caused by the nut between the seat and the handlebars. Make sure yours isn't too tight or too loose.
IP Logged
Mekh
Full Member
Offline
Suzuki Savage Rocks!
Posts: 128
Denmark
Gender:
Re: Piston ring end gap (free)
Reply #2 -
01/14/17 at 00:03:34
I will be measuring the cylinder and piston today, but I'd be surprised if it turns out to be worn significantly, based on the looks of them.
With regards to free end gap. What I cannot make sense of, is that the wear limit is a smaller distance than the spec. distance and not larger. Can someone explain this!?
Back to top
IP Logged
youzguyz
Serious Thumper
Offline
Posts: 2538
San Antonio, Texas
Gender:
Re: Piston ring end gap (free)
Reply #3 -
01/14/17 at 01:17:46
Mekh wrote
on 01/14/17 at 00:03:34:
I will be measuring the cylinder and piston today, but I'd be surprised if it turns out to be worn significantly, based on the looks of them.
With regards to free end gap. What I cannot make sense of, is that the wear limit is a smaller distance than the spec. distance and not larger. Can someone explain this!?
Think of the ring as a compression type spring.
The larger the gap, the more force the spring can produce when it is compressed as it tries to return to it's "free" state.
As the ring gets older, it loses the ability to spring back to it's original size (the larger free end gap).
Therefore, smaller gap = more worn out.
Back to top
2002 - Silver (Thumper)
2000 - Green (Mad Hamish)
Most motorcycle problems are caused by the nut between the seat and the handlebars. Make sure yours isn't too tight or too loose.
IP Logged
Dave
YaBB Moderator
ModSquad
Offline
SuzukiSavage.com
Rocks!
Posts: 18101
Camp Springs, Kentucky
Gender:
Re: Piston ring end gap (free)
Reply #4 -
01/14/17 at 03:34:43
Youzguys is correct, the "free end gap" is a measure of the "springiness" left in the ring. As the ring becomes fatigued is loses it's ability to open back up and apply pressure against the cylinder wall.
The free end gap however is not a measure of the wear on the piston ring, and that must be measured with the piston ring inside the top edge of the cylinder - but far enough down so you are not on the ridge at the top of the cylinder where the rings never travel. The ring end gap within the cylinder should be 0.30 - 0.45mm, and it is worn out when it reaches 1.0mm. The closer the rings are to 0.45mm the less worn they are....the closer they are to 1.0 mm the more worn out they are.
If you are re-using the rings.....you probably don't need to hone the cylinder as the rings are broken in and used to running in that cylinder. If you install new rings - you need to hone the cylinder so that the rings will have a surface that can allow them to break in properly.
Back to top
Someday I will be old......But not today!
IP Logged
Mekh
Full Member
Offline
Suzuki Savage Rocks!
Posts: 128
Denmark
Gender:
Re: Piston ring end gap (free)
Reply #5 -
01/14/17 at 04:44:32
Thank you, that makes sense. I was not considering that it could loose its "springiness" over time. Must be some kind of temperature induced creep...
So... Considering the measurements in my OP, I suppose ring 1 is OK, but ring 2 is worn beyond the wear limit. Correct?
Back to top
IP Logged
Armen
Serious Thumper
Offline
Half-Witted
Wrench-Jockey from
Jersey
Posts: 1452
Re: Piston ring end gap (free)
Reply #6 -
01/14/17 at 07:35:56
FWIW, the ring set is in the low $30's. If you are that far into the bike, it makes sense to swap in new ones.
Back to top
In theory, theory and reality are the same. In reality, they aren't...
IP Logged
Mekh
Full Member
Offline
Suzuki Savage Rocks!
Posts: 128
Denmark
Gender:
Re: Piston ring end gap (free)
Reply #7 -
01/14/17 at 13:09:05
Around here it is 70-75$ for a ring set...
http://www.mc-importen.dk/wop/
Back to top
IP Logged
Armen
Serious Thumper
Offline
Half-Witted
Wrench-Jockey from
Jersey
Posts: 1452
Re: Piston ring end gap (free)
Reply #8 -
01/14/17 at 14:21:21
Ouch!
Back to top
In theory, theory and reality are the same. In reality, they aren't...
IP Logged
Pages: 1
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
09/30/24 at 14:31:43
›
General Category
›
Rubber Side Down!
› Piston ring end gap (free)
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.