SuzukiSavage.com - Disc drilling

Donate!

Welcome, Guest. Please Login or Register :: View Members

SuzukiSavage.com › General Category › Rubber Side Down! › Disc drilling

(Moderators: verslagen1, Dave, Serowbot)

‹ Previous topic | Next topic ›

Pages: 1 2

Send Topic

Print

Disc drilling (Read 167 times)

Armen Serious Thumper Offline Half-Witted Wrench-Jockey from Jersey Posts: 1452	Disc drilling 08/05/16 at 18:14:19 Not much metal in these discs, so I only poked a few holes in.
Back to top	Disc_done.JPG In theory, theory and reality are the same. In reality, they aren't... IP Logged

Kris01 Serious Thumper Offline Eat, sleep, RIDE! Posts: 3767 Tennessee Gender:	Re: Disc drilling Reply #1 - 08/05/16 at 18:22:55 Think it will do any good?
Back to top	There's no problem that a full tank of gas and a sunny day can't fix! 2008 S40, Rotella T 15W-40 w/ZDDP added, Dyna, 140/90-15, Battery Tender Jr., Seat lift, #52.5/150/3 washers, Raptor IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28903 L.A. California Gender:	Re: Disc drilling Reply #2 - 08/05/16 at 18:31:02 in between the patterns of three... you need a pattern of 2 so that the whole pad is swept. I think the holes do a lot of good, since I've had them, I don't have to clean the disc every so often to keep it from squealing.
Back to top	Versey's Place Tech Section Index IP Logged

justin_o_guy2 Serious Thumper Offline What happened? Posts: 55279 East Texas, 1/2 dallas/la.	Re: Disc drilling Reply #3 - 08/05/16 at 19:39:50 What size holes?
Back to top	The people never give up their liberties but under some delusion.- Edmund Burke. IP Logged

Armen Serious Thumper Offline Half-Witted Wrench-Jockey from Jersey Posts: 1452	Re: Disc drilling Reply #4 - 08/08/16 at 18:02:08 Verslagen1 Like this? Almost didn't bother, but I threw the disc back on the jig and wrote an extra few steps on the program. If I did it again, I'd prob do fewer holes. The disc is pretty minimal.
Back to top	Savage_disc_II.jpg In theory, theory and reality are the same. In reality, they aren't... IP Logged

justin_o_guy2 Serious Thumper Offline What happened? Posts: 55279 East Texas, 1/2 dallas/la.	Re: Disc drilling Reply #5 - 08/08/16 at 19:27:06 justin_o_guy2 wrote on 08/05/16 at 19:39:50: What size holes?
Back to top	The people never give up their liberties but under some delusion.- Edmund Burke. IP Logged

zipidachimp Serious Thumper Offline SuzukiSavage.com Rocks! Posts: 1429 surrey, b.c. Gender:	Re: Disc drilling Reply #6 - 08/08/16 at 21:49:51 Holes work against friction, less material, but they look cool!
Back to top	IP Logged

justin_o_guy2 Serious Thumper Offline What happened? Posts: 55279 East Texas, 1/2 dallas/la.	Re: Disc drilling Reply #7 - 08/08/16 at 21:57:07 Guys, I'm planning on doing it.. What size holes are you using?
Back to top	The people never give up their liberties but under some delusion.- Edmund Burke. IP Logged

justin_o_guy2 Serious Thumper Offline What happened? Posts: 55279 East Texas, 1/2 dallas/la.	Re: Disc drilling Reply #8 - 08/08/16 at 21:58:12 zipidachimp wrote on 08/08/16 at 21:49:51: Holes work against friction, less material, but they look cool! Dust moves out, air cools, too many is bad..
Back to top	The people never give up their liberties but under some delusion.- Edmund Burke. IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28903 L.A. California Gender:	Re: Disc drilling Reply #9 - 08/08/16 at 21:58:33 3/16"
Back to top	Versey's Place Tech Section Index IP Logged

justin_o_guy2 Serious Thumper Offline What happened? Posts: 55279 East Texas, 1/2 dallas/la.	Re: Disc drilling Reply #10 - 08/08/16 at 22:07:28 Thanks,
Back to top	The people never give up their liberties but under some delusion.- Edmund Burke. IP Logged

Kenny G Serious Thumper Offline SuzukiSavage.com The Singles Club...LOL Posts: 1754 Robson Ranch, Denton, Texas Gender:	Re: Disc drilling Reply #11 - 08/08/16 at 22:57:30 Armen, What would you charge to drill a disk for guys on the forum? Kenny G
Back to top	IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28903 L.A. California Gender:	Re: Disc drilling Reply #12 - 08/08/16 at 23:20:44 Armen wrote on 08/08/16 at 18:02:08: Verslagen1 Like this? Almost didn't bother, but I threw the disc back on the jig and wrote an extra few steps on the program. If I did it again, I'd prob do fewer holes. The disc is pretty minimal. Yep, nice pattern, I may steal it from you.
Back to top	Versey's Place Tech Section Index IP Logged

Armen Serious Thumper Offline Half-Witted Wrench-Jockey from Jersey Posts: 1452	Re: Disc drilling Reply #13 - 08/09/16 at 05:21:40 Help yourself Verslagen. I might go to 8 sets of holes to give a little more metal between the holes. That and rotate the pattern so that the holes aren't near the arms. I used incrementally larger bits as the holes went toward the perimiter.
Back to top	In theory, theory and reality are the same. In reality, they aren't... IP Logged

Dave YaBB Moderator ModSquad Offline SuzukiSavage.com Rocks! Posts: 18137 Camp Springs, Kentucky Gender:	Re: Disc drilling Reply #14 - 08/09/16 at 05:35:01 I don't have a CNC, or anything that would help to get the radial/circular swept pattern done evenly.....so I just used a protractor and my drill press. I drilled 2 holes in alternating paths. Your patterns look nicer - this one works and is easier for us amateurs!
Back to top	Disc.jpg Someday I will be old......But not today! IP Logged

Pages: 1 2

Send Topic

Print

‹ Previous topic | Next topic ›

« Home