SuzukiSavage.com - Front footpeg torque spec?

Welcome, Guest. Please Login or Register :: View Members

SuzukiSavage.com › General Category › Rubber Side Down! › Front footpeg torque spec?

(Moderators: verslagen1, Dave, Serowbot)

‹ Previous topic | Next topic ›

Pages: 1

Front footpeg torque spec? (Read 56 times)

Redryder652 Full Member Offline SuzukiSavage.com Rocks! Posts: 179 Bergen County, New jersey Gender:	Front footpeg torque spec? 07/11/16 at 15:12:25 I tightened the front right footpeg mounting nuts that hold the exhaust shield to about 30 ft-lb. Is this right? I don't want to crush the case...
Back to top	IP Logged

Dave YaBB Moderator ModSquad Offline SuzukiSavage.com Rocks! Posts: 18099 Camp Springs, Kentucky Gender:	Re: Front footpeg torque spec? Reply #1 - 07/11/16 at 18:42:04 I could look it up for you....but then the next time you need to tighten something you would have to ask again Go to the Tech Section of this forum, look up the Table of Contents, and find the chart for the torque specs.
Back to top	Someday I will be old......But not today! IP Logged

Redryder652

Full Member

Offline

SuzukiSavage.com
Rocks!

Posts: 179
Bergen County, New jersey
Gender: male

Re: Front footpeg torque spec?
Reply #2 - 07/11/16 at 18:45:23

Dave wrote on 07/11/16 at 18:42:04:

I could look it up for you....but then the next time you need to tighten something you would have to ask again

Go to the Tech Section of this forum, look up the Table of Contents, and find the chart for the torque specs.

Ahh... Well I feel dumb now. Didn't know there was a torque spec page and here I am asking all the time... Well thank you for the feedback.

IP Logged

Kris01 Serious Thumper Offline Eat, sleep, RIDE! Posts: 3767 Tennessee Gender:	Re: Front footpeg torque spec? Reply #3 - 07/11/16 at 18:56:51 http://suzukisavage.com/cgi-bin/YaBB.pl?num=1098848534 I've been through the Tech section a bazillion times. I don't think I ever opened that page!
Back to top	There's no problem that a full tank of gas and a sunny day can't fix! 2008 S40, Rotella T 15W-40 w/ZDDP added, Dyna, 140/90-15, Battery Tender Jr., Seat lift, #52.5/150/3 washers, Raptor IP Logged

Dave YaBB Moderator ModSquad Offline SuzukiSavage.com Rocks! Posts: 18099 Camp Springs, Kentucky Gender:	Re: Front footpeg torque spec? Reply #4 - 07/12/16 at 03:16:02 Redryder652 wrote on 07/11/16 at 18:45:23: Ahh... Well I feel dumb now. Didn't know there was a torque spec page and here I am asking all the time... Well thank you for the feedback. No need to feel dumb......just feel enlightened!
Back to top	Someday I will be old......But not today! IP Logged

Tocsik Serious Thumper Offline the singularity Posts: 1163 Denver, CO Gender:	Re: Front footpeg torque spec? Reply #5 - 07/12/16 at 05:56:04 I keep that chart in a plastic sleeve attached to the outside of my tool chest with a magnetic clip. Along with a couple torque conversion charts.
Back to top	'08\|Raptor\|Dyna\|Stock jets & no other carb changes @ 5280' alt\|'slavy CCT\|Kawa front pulley\|130/90 rear tire\|7" LED headlight\|3" straight risers\|FIAMM El Grande horns\|Mutazu hard bags IP Logged

Pages: 1

‹ Previous topic | Next topic ›

« Home