SuzukiSavage.com - Decompression cable adjustment?

Welcome, Guest. Please Login or Register :: View Members

SuzukiSavage.com › General Category › Rubber Side Down! › Decompression cable adjustment?

(Moderators: verslagen1, Dave, Serowbot)

‹ Previous topic | Next topic ›

Pages: 1

Decompression cable adjustment? (Read 78 times)

Savageman Senior Member Offline Knowledge is half the battle Posts: 275 Marysville, California Gender:	Decompression cable adjustment? 12/10/15 at 19:21:14 Does any Savage Guru know the correct way to adjust the decompression solenoid cable? Clymer doesn't. It is supposed to hold open the exhaust valves for for a 1/3 or 1/2 second so the starter motor comes up to speed and cranks the beast.
Back to top	IP Logged

oldNslow Serious Thumper Offline SuzukiSavage.com Rocks! Posts: 2683 Rochester, NY Gender:	Re: Decompression cable adjustment? Reply #1 - 12/10/15 at 19:31:07 http://suzukisavage.com/cgi-bin/YaBB.pl?num=1169356966
Back to top	IP Logged

Savageman

Senior Member

Offline

Knowledge is half
the battle

Posts: 275
Marysville, California
Gender: male

Re: Decompression cable adjustment?
Reply #2 - 12/10/15 at 20:12:44

Thanks for the quick response.

I still have questions though Undecided

It states to place at TDC ok, and measure for 3 to 5mm of solenoid throw ok, BUT there is no way your fingers can provide enough force to push the plunger in all the way to open the exhaust valves. So are they saying 3 to 5mm of plunger travel will be adequate to open the exhaust valves Hmmm? My starter does have a tough time cranking right at first compression stroke. Battery is good 14.7volts with a trickle charger on it.

I'm thinking 2 to 3mm of travel will work better?

IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28886 L.A. California Gender:	Re: Decompression cable adjustment? Reply #3 - 12/10/15 at 21:17:54 Savageman wrote on 12/10/15 at 20:12:44: I'm thinking 2 to 3mm of travel will work better? too tight may stall the solenoid
Back to top	Versey's Place Tech Section Index IP Logged

Steve H Serious Thumper Offline SuzukiSavage.com Rocks! Posts: 1223 Spartanburg, SC Gender:	Re: Decompression cable adjustment? Reply #4 - 12/11/15 at 04:39:25 The adjustment procedure is in Clymer's on p 48 & 49. You're looking for 3-5mm of slack to give the solenoid time to get moving before it starts pulling.
Back to top	87 LS650, 2005 Ninja 250, 2009 Yamaha C3, 2001 Honda Reflex. On 2 wheels since 6/80. IP Logged

justin_o_guy2 Serious Thumper Offline What happened? Posts: 55279 East Texas, 1/2 dallas/la.	Re: Decompression cable adjustment? Reply #5 - 12/11/15 at 07:25:52 I know how that works. I needed almost two full steps to get the gym doors open. And Ray Parent could smash one open with a dodge ball from half court. Should I explain what happened when he put one in my ear as I was walking off, after being put out?
Back to top	The people never give up their liberties but under some delusion.- Edmund Burke. IP Logged

Pages: 1

‹ Previous topic | Next topic ›

« Home