Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› Head Gasket and Head Cap Install
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages:
1
2
Head Gasket and Head Cap Install (Read 309 times)
Oldfeller--FSO
Serious Thumper
ModSquad
Offline
Hobby is now
"concentrated
neuropany"
Posts: 12673
Fayetteville, NC
Gender:
Re: Head Gasket and Head Cap Install
Reply #15 -
03/08/13 at 08:17:31
justin_o_guy2 wrote
on 03/04/13 at 08:42:58:
Wheres the crushed up brillo pad stuff?
If it behaves normally, it stays scrunched up inside the recess in the cover half. But you are right, it should be checked to make sure it is still there when you put the thing back together.
Back to top
Former Savage Owner
IP Logged
Rocket
YaBB Newbies
Offline
SuzukiSavage.com
Rocks!
Posts: 13
Re: Head Gasket and Head Cap Install
Reply #16 -
03/11/13 at 09:28:27
I just finished assembly of head gasket and cap last night. I wish I'd passed on the head gasket as it is a lot more work than just doing the cap, and as I examined things once they were apart, it appears there was really nothing wrong with the head gasket and oil was leaking down from the area below the cap. Ah well!
On another note, I worry (and will till I start the bike!) that I may not have the cam chain exactly aligned with the crank. I did have the bike at TDC per the little "T" mark on the left flywheel (?) and the two marks on the cam parallel to the top of the head, but I worry that there is a little bit of subjectivity in whether the 'T' is perfectly aligned. Thinking back I didn't try changing the chain on the cam gear one link to the left and one link to the right to see if I could make the alignment even better. Any thoughts on this issue?
Thanks ...Rocket
Back to top
IP Logged
verslagen1
YaBB Moderator
ModSquad
Offline
Where there's a
will, I want to be
in it.
Posts: 28886
L.A. California
Gender:
Re: Head Gasket and Head Cap Install
Reply #17 -
03/11/13 at 10:17:51
With a brand new chain, and the TDC mark lined up, the cam marks will line up perfectly horizontal.
With a used chain, stretched a bit, the front side, which is straight, will be a little longer. So the cam marks will be a little raised on that side.
I would try to get it to show slightly below then set it to the next tooth over for slightly above.
One tooth off and it won't run right, but not explode. More than that can't tell you. No ones ever admitted to more.
Back to top
Versey's Place
Tech Section Index
IP Logged
Rocket
YaBB Newbies
Offline
SuzukiSavage.com
Rocks!
Posts: 13
Re: Head Gasket and Head Cap Install
Reply #18 -
03/11/13 at 10:50:23
Thanks. I already buttoned it up, but if it won't run right, I'll know where to look. If its off, its only one tooth so I won't blow it up!
Back to top
IP Logged
Pages:
1
2
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
09/28/24 at 23:25:59
›
General Category
›
Rubber Side Down!
› Head Gasket and Head Cap Install
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.