SuzukiSavage.com - Hi Everyone. First post, which is also a question

dadface

YaBB Newbies

Offline

SuzukiSavage.com
Rocks!

Posts: 6
Carlsbad, NM
Gender: male

Hi Everyone. First post, which is also a question
01/07/13 at 14:55:41

Hi everyone,

My name is Matt, and I have recently acquired a 1988 Suzuki Savage!!
The folks that I bought it from said it needed a new "starter gear". In my infinite wisdom, I thought that meant starter motor. NOT SO!! I am having to replace the single sprocket that connects directly to the starter motor, the intermediate sprocket with two sets of teeth (one of which is the approximate radius of the aforementioned gear, the second of which is much smaller). these two gears are nicely photographed on an earlier post. The third and final part needing replacement is the large sprocket that rests behind the magnet and I think it is the starter clutch???

In any case, I have the parts in hand, and cannot for the life of me figure out how to get the magnet off such that I can replace the large starter clutch gear. Here are some thoughts...

1. Start the destruction!! Grin

There is a large bolt that nests in a larger bolt in the center of the assembly that I can see from the outside. This connects to the crankshaft. My gut feeling is removing this bolt will not really accomplish my goal.

2. There are six allen head bolts that connect the large magnet to something...they are of a seemingly odd size, but if I were to remobe these, would I be able to remove the magnet and access the sprocket behind it?

Traditionally, I generally use strategy one and start tearing stuff apart and let god sort em out, but I have just turned 30, and, in the interest of pretending to have some semblance of maturity/patience, decided that a new approach (educate myself before breaking more stuff/creating more work for myself) might be appropriate.

Thanks all in advance and looking forward to being a part of this wonderful forum!!

Cheers and Best Regards,
Matt

Back to top

IP Logged

Digger

Serious Thumper
2005 No Login

Offline

Ya gotta be tough to
ride singles!

Posts: 1604
Colorado Springs, CO
Gender: male

Re: Hi Everyone. First post, which is also a ques
Reply #1 - 01/07/13 at 19:35:32

dadf,

Welcome to the forum, and congrats on the new (to you) bike....

While there are scads of people here who could answer your specific question, I fear that you would then have "a little knowledge," which, of course, can be very dangerous.

May I suggest that you invest in a service manual before diving into this job? I'm sure that you'll still have questions, but we'd feel better about answering same if we were relatively sure we would not be contributing to possible mayhem.....

Cheers!

Back to top

Digger
2001, Metallic Glacial Blue, Raptor Petcock, Verslavy (first hole) (otherwise, mechanically, the bike is stock), 13,xxx miles
I don't own a cage.
www.astronautbiker.com

IP Logged

SALB Serious Thumper Offline FSO Posts: 668 Whittier, AK Gender:	Re: Hi Everyone. First post, which is also a ques Reply #2 - 01/07/13 at 19:41:22 Downloadable manuals. http://suzukisavage.com/cgi-bin/YaBB.pl?board=tech;action=display;num=1138554254
Back to top	IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28903 L.A. California Gender:	Re: Hi Everyone. First post, which is also a ques Reply #3 - 01/07/13 at 20:33:39 You need a tool to remove the rotor. those 6 bolts hold the starter gear to the backside, so removing them will do nothing.
Back to top	Versey's Place Tech Section Index IP Logged

jcstokes Serious Thumper Offline SuzukiSavage.com is very useful Posts: 2119 Mauku New Zealand Gender:	Re: Hi Everyone. First post, which is also a ques Reply #4 - 01/07/13 at 20:56:10 Later model starters had something which prevented a breakage of the starter clutch thingy, if the engine backfired during start up. Hope you have one of those and there should be plenty of people who can give accurate guidance on this point.
Back to top	Completely stock 2010 S40, aftermarket rev counter and back pack, Airhawk seat pad IP Logged

dadface

YaBB Newbies

Offline

SuzukiSavage.com
Rocks!

Posts: 6
Carlsbad, NM
Gender: male

Re: Hi Everyone. First post, which is also a ques
Reply #5 - 01/08/13 at 07:41:00

Hi all,

Thanks for the link to downloadable service manual. That will most certainly come in handy!! A little more background.. I like to buy old barn bikes and fix them up to ride for a while and resell for break even/small profit, that way I can ride for (pretty much) free and have a new bike every year or so. Mostly, I have dealt with smaller twins (400ish cc). This is my first 650 and my first single, so i'm really excited to get it moving!!

After some amount of research, I (as Verslagen states) need a magneto puller. I found one for $40 on pitposse. Anyone have experience w/ these guys? I would just have the theiving dealer pull it for me, but the closest one is 150 miles away.....cheaper to buy the tools myself.

In order to use this tool, I have to remove the bolt that is in the front of the assembly (method #1 above)...have tried anti-seize and a breaker bar. That fu@#er is on there!! Do you guys think using a torch and applying heat will hurt anything in the starter clutch and/or any other tips to get that little guy to break loose?

Thanks for all of the helpful advice!! My eventual goal is to do a RYCA/semi RYCA conversion to this bike, so I am sure that I will need some more help haha!

@ Verslagen....do you still make the cam chain tension devices, I would very much like to have one of those brilliant little things!!

Back to top

IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28903 L.A. California Gender:	Re: Hi Everyone. First post, which is also a ques Reply #6 - 01/08/13 at 08:55:32 Usually, that only torqued on. but the PO may have popped it loose turning it to TDC and got tired of that and used locktite. I'd apply heat and pen oil. BTW it goes CCW to loosen... i think. yes, still making them, some day I'll get caught up too. see the marketplace, follow the links and instructions.
Back to top	Versey's Place Tech Section Index IP Logged

dadface YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 6 Carlsbad, NM Gender:	Re: Hi Everyone. First post, which is also a ques Reply #7 - 01/08/13 at 09:17:08 I would like to go ahead and add myself to your list if possible. The email link isn't working on this cpu (i'm at work), and I cannot yet pm. Would you mind pm-ing me your email address, and I will send you an email with my contact info and the information that you request on your store page. Thanks!!
Back to top	IP Logged

ToesNose Serious Thumper Offline Pardon me, do you have Hot Sauce? Posts: 1993 Mooresville, NC Gender:	Re: Hi Everyone. First post, which is also a ques Reply #8 - 01/09/13 at 12:59:23 Welcome! And best of luck getting it all sorted out
Back to top	The Suzuki LS650, bringing Miles of Smiles everywhere! IP Logged

dadface

YaBB Newbies

Offline

SuzukiSavage.com
Rocks!

Posts: 6
Carlsbad, NM
Gender: male

Re: Hi Everyone. First post, which is also a ques
Reply #9 - 01/15/13 at 09:53:40

Thanks!!

So I got the flywheel puller in yesterday and put in all of the new starting system gears, changed the oil/filter, put in a new battery and was ready for the initial (fingers crossed that it will run) cranking of the engine...

and nothing..... ahh it would have been too easy haha!

a question that I would like to pose is this:

can you all feel the engine turning over when you start your bikes??
I would think that the single big ol' cylinder in these machines would make itself known...(unless the decompression solonoid/switch thingy negates this...)

The reason that I ask is that the starter motor is spinning, but I don't really hear/feel compression notes from the engine/exhaust...I know that the bike has compression (tested it sort of..). Is it possible to
install the starter clutch incorrectly such that it does not catch the way it should?? When re-assembling it, it seemed that there was only one way to put it on, but I have been wrong before.... Undecided

And yep, that @#%&ing 17mm bolt is lefty loosy.

Back to top

IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28903 L.A. California Gender:	Re: Hi Everyone. First post, which is also a ques Reply #10 - 01/15/13 at 11:42:03 You mighta put it on backwards, not sure. take the starter out, stick you finger against the gear, it should lock up one way and spin the other. There's a gear inbetween the idler and the clutch so the idler should spin the same way as the crank... which is CCW as viewed from the left side.
Back to top	Versey's Place Tech Section Index IP Logged

Bubba

Serious Thumper

Offline

SuzukiSavage.com
Rocks!

Posts: 956
Denver, CO
Gender: male

Re: Hi Everyone. First post, which is also a ques
Reply #11 - 01/15/13 at 13:05:56

If it's cranking but
Edited:

it's not turning

then you may have positioned the washers incorrectly....
like these starter gear washers...
http://www.ronayersmotorcycles.com/fiche_section_detail.asp?section=298925&ca...

I had the same problem on a '96 that I fixed for my friend...the washer was on the wrong gear and it would turn over but not catch...

Back to top

« Last Edit: 01/15/13 at 14:37:13 by verslagen1 »

'06 lt Blue, Dyna Power pipe, air screw 2 1/4 turns, 52.5 pilot w/ bleed holes, 150 Main, 2/3 spacer, Pirelli MT66 tires, Raptor petcock, 412-4006 Progressive shocks

IP Logged

dadface

YaBB Newbies

Offline

SuzukiSavage.com
Rocks!

Posts: 6
Carlsbad, NM
Gender: male

Re: Hi Everyone. First post, which is also a ques
Reply #12 - 03/27/13 at 15:52:08

hey all,

sorry, had to go out of town for a coupla/few months for work. just got back and at it!! So the starter clutch was backwards...

well darn...

anyway, got that fixed up and pulled off the other side of the crank cover....

darn!!! time for a verslavy! .... @verslagen...(can i get your full contact info (name, home address,city state zip??) cuz i've got a blank to send you in exchange for one of your materpieces....as well as a check for the difference...)

thanks man!!

btw, do any of you guys love (bands) Rush, Tool, Dream Theatre??

AWESOME garage wrenching music....

Cheers and Regards all (and thanks for the help/advice)
--Matt

Back to top

IP Logged

Serowbot YaBB Moderator ModSquad Offline OK.... so what's the speed of dark? Posts: 28846 Tucson Az Gender:	Re: Hi Everyone. First post, which is also a ques Reply #13 - 03/27/13 at 16:27:21 Contact Versy here... ... Contacted I don't know about you guys, but the email button works fine =v1
Back to top	« Last Edit: 03/27/13 at 19:36:11 by verslagen1 » Ludicrous Speed !... ... ... IP Logged

dadface

YaBB Newbies

Offline

SuzukiSavage.com
Rocks!

Posts: 6
Carlsbad, NM
Gender: male

Re: Hi Everyone. First post, which is also a ques
Reply #14 - 09/25/13 at 17:05:42

Hello again all,

So I got the cam chain tensioner on (thanks verslagen!!), fixed a couple of oil leaks, cleaned the carbs, and tried to start the beast. no luck.

I checked for spark by placing the plug against the heat sink fins on the block while turning the engine over, and got a negative result. Bought a new plug. still no spark. Replaced the ignition coil. still negative. took apart the black tci box and everything in there looks okay.

do you guys have any suggestions on what I should do to get a spark?
I am wondering if it has anything to do with the triple super awesome safety system on these bikes (side stand is in up position for all earlier testing..)?

Thanks!!
Matt

Back to top

IP Logged