Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› How do the bar ends attach?
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages: 1
How do the bar ends attach? (Read 82 times)
nuster
YaBB Newbies
Offline
SuzukiSavage.com
Rocks!
Posts: 19
How do the bar ends attach?
05/31/12 at 18:00:07
I may want to replace with bar end weights to dampen vibration & stick past the levers to protect them. My daughter will begin to ride her 2012 S40 in two weeks after her MSF class. I would hate her to scuff it up in a 0-2 mph drop, stumble, slip, clutch, curb type slow speed learning stuff. Some bikes you can lift off the sidestand, let them drop and be hard to find damage. Others have a dented tank, bent internal shifting forks, broken levers, ect. I am trying to make her bike the former. If I get the courage I will post a picture of the 24" cross bar I am temporarily adding to the top of the Suzuki case guards. At least the photo will include the water pipe home made bike lift.
Back to top
IP Logged
SimonTuffGuy
Serious Thumper
Alliance Member
Offline
i like to thump...
;)
Posts: 1159
Central PA
Gender:
Re: How do the bar ends attach?
Reply #1 -
05/31/12 at 18:11:15
The bar end weights are welded in place. If you remove the grips, you'll see the 2 weld marks on the bottom side of the bar. And it's not no tiny little spot weld.
I removed mine from my stock bars, but ruined the bars in the process.
Back to top
Simon
Pimptiva.com
IP Logged
Serowbot
YaBB Moderator
ModSquad
Offline
OK.... so what's the
speed of dark?
Posts: 28657
Tucson Az
Gender:
Re: How do the bar ends attach?
Reply #2 -
05/31/12 at 18:47:21
I think he means the little chrome plastic caps... they just pull off...
...but the stock bars are slugged with huge welded in weights...
You can't get those out. like Simon says... it's hopeless...
If you want bar ends... you'll have to buy new bars...
Back to top
Ludicrous Speed !... ...
...
IP Logged
nuster
YaBB Newbies
Offline
SuzukiSavage.com
Rocks!
Posts: 19
Re: How do the bar ends attach?
Reply #3 -
05/31/12 at 19:02:15
Thanks for the info. I will not pull the plastic caps off since they have weights welded in. So that area is on it's own. After the 600 mile service I will remove the brass plug and hopefully improve the flat spot right of Idle. That is enough to knock a newbie over LOL.
Back to top
IP Logged
jay313
YaBB Newbies
Offline
SuzukiSavage.com
Rocks!
Posts: 15
Re: How do the bar ends attach?
Reply #4 -
06/01/12 at 05:09:33
Parking lot falls are most common for newbies. Just buy some crash bars and remove them next year. That should keep the worst from happening.
Back to top
IP Logged
360k+
Serious Thumper
Offline
Savage heart of
darkness
Posts: 680
Cartersville, GA
Gender:
Re: How do the bar ends attach?
Reply #5 -
06/01/12 at 18:43:20
SimonTuffGuy wrote
on 05/31/12 at 18:11:15:
The bar end weights are welded in place. If you remove the grips, you'll see the 2 weld marks on the bottom side of the bar. And it's not no tiny little spot weld.
I removed mine from my stock bars, but ruined the bars in the process.
Simon, were the weights steel, brass, or what? And do you remember about how big/long they were or how much they weighed?
Back to top
The JOURNEY is the reward!
IP Logged
Pages: 1
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
09/27/24 at 00:27:51
›
General Category
›
Rubber Side Down!
› How do the bar ends attach?
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.