SuzukiSavage.com - Straighten Bent Clutch/Break Lever

stamper

YaBB Newbies

Offline

Savage Thumpin'

Posts: 7
Managua
Gender: male

Straighten Bent Clutch/Break Lever
04/26/12 at 23:39:34

1) First buy a new one, no trick is fool proof. If you are successful you have a spare. If not, you can still ride and wait for the next bender.
2) Rub the area of the bend with a wet piece of soap.
3) Heat the lever on a gas burner until the soap is shiny dark brown/ black. This is to soften the duraluminium. (or duralumin if you say so)
4) Throw it in a bucket of cold water.
5) Use a plastic, or hard rubber hammer on a trunk of wood or a block of lead to straighten it back in shape. Or bend it back in a vice. Or both.
6) The hardness will return after some days but the soft lever is strong enough to use.

I have bent one lever 3 times back to the original shape.

I shaped dural sheet by hand in my profession and the day began with softening it as above. I have no idea what the science behind it is, but it just works.

I hope you do not crash your precious thumper and bend the ears, but in case you do, good luck.

Back to top

IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28749 L.A. California Gender:	Re: Straighten Bent Clutch/Break Lever Reply #1 - 04/26/12 at 23:53:48 neat trick to tell when the lever is hot enough to be annealed. aluminum hardens at room temperature. takes about a week to get to what is called T4 when we send out a sheet of aluminum to be annealed, it has to be returned on ice or it'll harden.
Back to top	Versey's Place Tech Section Index IP Logged

stamper

YaBB Newbies

Offline

Savage Thumpin'

Posts: 7
Managua
Gender: male

Re: Straighten Bent Clutch/Break Lever
Reply #2 - 04/27/12 at 22:24:55

Dear Verslagen,

The other trick is to heat the dural and write on it with a matchstick
( the wood) If the temp is ok, it will leave a black trail. The soap trick is easier. Use the matchstick if you do not have soap.
(but who does not have a bar of soap in this forum? Embarrassed

)

I make limb prostheses for a living and 40 years ago, many where still made from alumininum. The socket was cut out of a sheet, bended into a pipe , riveted and then the shape made with hammers on metal bars or lead. Steel hammers to stretch and hard rubber to shrink. Thank god for plastic, the noise was unbearable. Just wondering why you still need annealed aluminium.

Wondering as well about your name! I am Dutch and verslagen sounds Dutch and means beaten (as in lost). (My name is peter poetsma).

If we have dural bars that are to soft, we keep them in the oven used daily around 200C and after several days they become harder.
I was told that the repeated slow cooling and heating changes the structure to becomes harder.

Its a pleasure to be part of the forum. lots to share and more to learn.
And just because I got me a S40. Good deal!

Went today to pick-up my saddle bags and saddle cushion by the local (horse) saddle maker. Now fiddling a way to keep them from touching the backwheel.

Greetings from Managua

Regards

Stamper (thats Dutch for thumper)

Back to top

IP Logged

verslagen1

YaBB Moderator
ModSquad

Offline

Where there's a
will, I want to be
in it.

Posts: 28749
L.A. California
Gender: male

Re: Straighten Bent Clutch/Break Lever
Reply #3 - 04/27/12 at 23:11:38

stamper = thumper Cool

I'm an aerospace engineer
we make high pressure, high temp aircraft ducting.
as well as various things for all sorts of things.
the tubes are made from sheet too.
huge presses that push sheet stock into platens of rubber.
two guys move the sheet along till it's a tube

I worked with an old german guy, every morning we'd exchange greetings
and his reply was "verslagena, terrible thank you"
initially, I figured that was similar to howlee or gringo in german.
He "called" me enough by that, I adopted it. and to him it meant terrible.
Like many words, it has multiple meanings, somewhere else it means report as well as beaten.
The multiple meanings fits my mood most of the time.

Back to top

Versey's Place
Tech Section Index

IP Logged

Serowbot YaBB Moderator ModSquad Offline OK.... so what's the speed of dark? Posts: 28361 Tucson Az Gender:	Re: Straighten Bent Clutch/Break Lever Reply #4 - 04/28/12 at 08:46:23 This is great!... I can't wait to try it... No,.. wait a minute... I can wait... ...
Back to top	Ludicrous Speed !... ... ... IP Logged

stamper

YaBB Newbies

Offline

Savage Thumpin'

Posts: 7
Managua
Gender: male

Re: Straighten Bent Clutch/Break Lever
Reply #5 - 06/14/12 at 22:55:20

Hi Verslagen,

Indeed, verslagen is as well the plural of verslag what means report in Dutch. Not much used but correct.
Someone asked me by PM why to put the lever in the cold water before bending. (Chris) I know but cannot (Error: You are only allowed to send Personal Messages if you've reached a post count of 10!)
Kury77 (Chris) wants to know. he wants to bend them closer to the bar.

Just fixed a crashbar and windscreen on the bike, super!!!

Back to top

IP Logged

stamper YaBB Newbies Offline Savage Thumpin' Posts: 7 Managua Gender:	Re: Straighten Bent Clutch/Break Lever Reply #6 - 06/14/12 at 23:03:07 Sorry, I realize i can answer here. dear kury77 (chris), after heating, you have to quench it in cold water to make/keep it soft. regards, peter
Back to top	IP Logged

kuri77 Full Member Offline SuzukiSavage.com Rocks! Posts: 127 Rancho Santa Margarita, Ca Gender:	Re: Straighten Bent Clutch/Break Lever Reply #7 - 06/16/12 at 17:17:12 Thanks Stamper but it kind of goes against what one would think in that cooling it off would make it harder again not keep it soft. Not arguing just saying that's why I PMed you. Bought a spare in case, so will try your method out next week.
Back to top	Big Sur IP Logged

stamper YaBB Newbies Offline Savage Thumpin' Posts: 7 Managua Gender:	Re: Straighten Bent Clutch/Break Lever Reply #8 - 06/17/12 at 18:10:23 Hi Kury77, For copper and aluminium: after heating and quenching it will be soft for some time. Steel is different. Success peter
Back to top	IP Logged