SuzukiSavage.com - valve cover

Nathaniel12345 YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 19	valve cover 04/12/12 at 15:41:15 hello, im attempting to do a Valve Adjustment and I cannot seem to get the back valve cover off. Im not sure if thats the Exhaust valve cover or the intake Valve cover. But, the frame is in the way so i really dont see how its possible to use a socket set without removing the engine. PLEASE HELP
Back to top	IP Logged

Serowbot YaBB Moderator ModSquad Offline OK.... so what's the speed of dark? Posts: 28850 Tucson Az Gender:	Re: valve cover Reply #1 - 04/12/12 at 15:51:15 Easy,... use a wrench, not a socket... The rear is the intake, front is the exhaust,... no such thing as a compression cover...
Back to top	Ludicrous Speed !... ... ... IP Logged

Nathaniel12345 YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 19	Re: valve cover Reply #2 - 04/12/12 at 15:54:51 o.. shows how much i know about bikes LOL. But, I tried a wrench and the bolt thingy basically deteriorates as i try to turn and does not budge a single bit. Im scared it may strip
Back to top	IP Logged

Serowbot

YaBB Moderator
ModSquad

Offline

OK.... so what's the
speed of dark?

Posts: 28850
Tucson Az
Gender: male

Re: valve cover
Reply #3 - 04/12/12 at 16:23:04

Nathaniel12345 wrote on 04/12/12 at 15:54:51:

o.. shows how much i know about bikes LOL.

... No offense,.. just letting you know... Wink

...

Are you using a box-end?... always use a box when you can...
Those nuts aren't supposed to be that tight, (I think about 12lbs is spec), (That's equal to thumb on the box, and firm fingers pulling wrench handle, no arm strength involved)...
...
To remove a stuck bolt...
Put the wrench on it, and tap the end of the wrench lightly (short, sharp taps) with a small hammer... Short, sharp, taps break the bite,.. steady muscle pressure will strip a head...
Best luck,.. (no shame in learning,.. we all do it)... (terminology, and problem solving, comes with time, and doing for yourself. It takes some mistakes and goofs to get there)...
It's an honorable thing to learn...
Wink

...

Back to top

Ludicrous Speed !... ... Huh

...

IP Logged

justin_o_guy2 Serious Thumper Offline What happened? Posts: 55279 East Texas, 1/2 dallas/la.	Re: valve cover Reply #4 - 04/12/12 at 17:46:58 Impact will release thngs that pressure will break. Put the box end on, hook another wrench on for a cheater & spank on it with an extension while you hold pressure on it. drizzling some Kroil on cant hurt.
Back to top	The people never give up their liberties but under some delusion.- Edmund Burke. IP Logged

Nathaniel12345 YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 19	Re: valve cover Reply #5 - 04/12/12 at 18:26:00 thanks guys.. i got one off, but the other one is stripped, and tight as hell! i was so close... now im soo far lol
Back to top	IP Logged

justin_o_guy2 Serious Thumper Offline What happened? Posts: 55279 East Texas, 1/2 dallas/la.	Re: valve cover Reply #6 - 04/12/12 at 18:48:41 What tool was on it when it stripped?
Back to top	The people never give up their liberties but under some delusion.- Edmund Burke. IP Logged

Nathaniel12345 YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 19	Re: valve cover Reply #7 - 04/12/12 at 19:38:40 well i just attempted to take this one off and i used a 10mm box wrench, the same one i used to take the other one off
Back to top	IP Logged

justin_o_guy2

Serious Thumper

Offline

What happened?

Posts: 55279
East Texas, 1/2 dallas/la.

Re: valve cover
Reply #8 - 04/12/12 at 20:38:56

12 point box end? You gotta make sure to keep them on level on the screw,,
If you can get to the head of the screw, & I know thats a big IF,, you can drive metal back where it came from,,& try again,, Or get a good pair of vise grips & IF you see them shifting, stop, same is true with a wrench, if the wrench is turning & your bolt hasnt given you that Snap,, Im coming loose,, stop.
I have tightened bolts that wouldnt loosen,, I mean just MOve it, then go the other way, back & forth,,saved a few that way,
Kroil,, or wintergreen oil.

If you can get a slap on that bolt, sometimes that helps them let go. a few quick taps can make a difference,

Once you get on it, remember,, pressure on the wrench + quick raps on the wrench,

Back to top

The people never give up their liberties but under some delusion.- Edmund Burke.

IP Logged

arteacher Serious Thumper Offline Ride as if your naked and invisable! Posts: 2581 London ontario Gender:	Re: valve cover Reply #9 - 04/13/12 at 04:10:07 Touch wood- I have never had any problem with any bolts on my bike.
Back to top	white '07, Raask exh, Corbin seat, slipstreamer shie, Raptor, Routy's fwd controls, Baron tach, Frisco bars, Isogrips, Headlight and taillight modulators, Dial-a- jet, AME 9 deg chop kit, K&N air flt IP Logged

justin_o_guy2 Serious Thumper Offline What happened? Posts: 55279 East Texas, 1/2 dallas/la.	Re: valve cover Reply #10 - 04/13/12 at 06:09:58 A 6 point socket with vise grips may be a start. Hey,, I can get my 1/4" ratchet & socket on them,, get a 6 point socket & dont just crank on it, use impact. YOu can use a deep socket with an extension for a cheater to put pressure on it. That moves your hand away far enough to take a wrench & spank on the thing.
Back to top	The people never give up their liberties but under some delusion.- Edmund Burke. IP Logged

Digger

Serious Thumper
2005 No Login

Offline

Ya gotta be tough to
ride singles!

Posts: 1604
Colorado Springs, CO
Gender: male

Re: valve cover
Reply #11 - 07/16/12 at 21:45:49

Nathaniel12345 wrote on 04/12/12 at 15:41:15:

hello, im attempting to do a Valve Adjustment and I cannot seem to get the back valve cover off. Im not sure if thats the Exhaust valve cover or the intake Valve cover. But, the frame is in the way so i really dont see how its possible to use a socket set without removing the engine. PLEASE HELP

For future reference....

Here's what I use the get those bolts out:

10mm GearWrench

This wrench works well here since the box end has no offset.

IHTH someone!

Back to top

Digger
2001, Metallic Glacial Blue, Raptor Petcock, Verslavy (first hole) (otherwise, mechanically, the bike is stock), 13,xxx miles
I don't own a cage.
www.astronautbiker.com

IP Logged

justin_o_guy2 Serious Thumper Offline What happened? Posts: 55279 East Texas, 1/2 dallas/la.	Re: valve cover Reply #12 - 07/16/12 at 23:33:30 You gotta whole set of them, didnt you? Daaang..
Back to top	The people never give up their liberties but under some delusion.- Edmund Burke. IP Logged

360k+ Serious Thumper Offline Savage heart of darkness Posts: 680 Cartersville, GA Gender:	Re: valve cover Reply #13 - 07/17/12 at 07:14:31 I know it's not supposed to be, but this is danged funny!
Back to top	The JOURNEY is the reward! IP Logged