Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› shifter linkage
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages: 1
shifter linkage (Read 71 times)
baker87
Junior Member
Offline
ridin since 06
Posts: 84
venus tx
Gender:
shifter linkage
04/01/12 at 09:43:07
what gear do u line up the shifter linkage in the shifter case
Back to top
ride hard/live hard
IP Logged
baker87
Junior Member
Offline
ridin since 06
Posts: 84
venus tx
Gender:
Re: shifter linkage
Reply #1 -
04/01/12 at 09:50:18
I downloaded and printed the clymer manual it says to line the 3rd teeth of the 5 teeth together... i did but it doesnt shift through al 5 just 2 gears....
Back to top
ride hard/live hard
IP Logged
verslagen1
YaBB Moderator
ModSquad
Offline
Where there's a
will, I want to be
in it.
Posts: 28886
L.A. California
Gender:
Re: shifter linkage
Reply #2 -
04/01/12 at 10:28:44
SSM says to line up center gears together.
the pawl should be in line between the two shafts.
Back to top
Versey's Place
Tech Section Index
IP Logged
baker87
Junior Member
Offline
ridin since 06
Posts: 84
venus tx
Gender:
Re: shifter linkage
Reply #3 -
04/01/12 at 11:00:41
Yep i lined the pawl with shifter spline arm and it shifts through 2 gears.... i can change gears and rotate pawl around and get all 5 gears and neutral.... but to set it in 1 gear and line up pawl i only have use of 1 and 2 gears
Back to top
ride hard/live hard
IP Logged
baker87
Junior Member
Offline
ridin since 06
Posts: 84
venus tx
Gender:
Re: shifter linkage
Reply #4 -
04/02/12 at 08:25:19
ok so i fixed the problem and now have all five gears and neutral.... my problem were the pawl springs were too long.....
Back to top
ride hard/live hard
IP Logged
justin_o_guy2
Serious Thumper
Offline
What happened?
Posts: 55279
East Texas, 1/2 dallas/la.
Re: shifter linkage
Reply #5 -
04/02/12 at 08:42:59
The stock springs were wrong?
Back to top
The people never give up their liberties but under some delusion.- Edmund Burke.
IP Logged
baker87
Junior Member
Offline
ridin since 06
Posts: 84
venus tx
Gender:
Re: shifter linkage
Reply #6 -
04/02/12 at 09:02:49
yep.... they also lined the piston rings together to..... it produced gouges in the cylinder.... the original owner was very hard on the bike also.... brand new off the show room floor and they were rompin on it.... the cam chain and tensioner have already been replaced by previous owner.... the driven trans shaft was spaced wrong to may washers inside..... so no 5th gear.... now i have 5th gear.... just ordered new rings honed the cylinder a miniscule amount.... maybe .0001 of an inch....
Back to top
ride hard/live hard
IP Logged
justin_o_guy2
Serious Thumper
Offline
What happened?
Posts: 55279
East Texas, 1/2 dallas/la.
Re: shifter linkage
Reply #7 -
04/02/12 at 09:22:18
they also lined the piston rings together to.
Sounds to me like your bike got intentionally vandalized from the factory,,
someone was angry,
Back to top
The people never give up their liberties but under some delusion.- Edmund Burke.
IP Logged
verslagen1
YaBB Moderator
ModSquad
Offline
Where there's a
will, I want to be
in it.
Posts: 28886
L.A. California
Gender:
Re: shifter linkage
Reply #8 -
04/02/12 at 11:28:01
Piston rings are known to rotate.
You finding them aligned is most likely a coinsidence.
Back to top
Versey's Place
Tech Section Index
IP Logged
Pages: 1
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
09/27/24 at 16:23:07
›
General Category
›
Rubber Side Down!
› shifter linkage
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.