SuzukiSavage.com - float hieght?

Welcome, Guest. Please Login or Register :: View Members

SuzukiSavage.com › General Category › Rubber Side Down! › float hieght?

(Moderators: verslagen1, Dave, Serowbot)

‹ Previous topic | Next topic ›

Pages: 1

float hieght? (Read 137 times)

seabeast77 YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 4	float hieght? 03/04/10 at 21:05:57 does anyone know the best float hieght for 1995 savage? and what is the easiest way to adjust and measure it? thanks for the info guys.
Back to top	IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28887 L.A. California Gender:	Re: float hieght? Reply #1 - 03/04/10 at 21:36:37 take a clear hose run it from the bottom of the carb up along the side and open the drain valve gas should come up a bit now turn the petcock to prime gas should come up to the gasket on the bowl
Back to top	Versey's Place Tech Section Index IP Logged

jabman Senior Member Offline Posts: 411 England Gender:	Re: float hieght? Reply #2 - 03/05/10 at 02:55:13 cool i need to do this where do you fit the tube? i cannot find any hole
Back to top	93" savage, 177.5 main, 52.5 w/holes 3 turns out , middle circlip, 6" k&n round filter, Dyna muffler, TKAT brace IP Logged

justin_o_guy2 Serious Thumper Offline What happened? Posts: 55279 East Texas, 1/2 dallas/la.	Re: float hieght? Reply #3 - 03/05/10 at 03:31:27 bottom of the bowl, little hang down with a screw poked in the side.
Back to top	The people never give up their liberties but under some delusion.- Edmund Burke. IP Logged

Reelthing

Serious Thumper
Alliance Member

Offline

Fish or ride that is
the question

Posts: 5397
Houston,Tx
Gender: male

Re: float hieght?
Reply #4 - 03/05/10 at 10:18:08

if that '95 is like mine it doesn't have a drain other than to remove the entire screw on the bottom - no place for the hose

unlike the '02 where the bottom of the bowl has a molded metal tube and the drain screw is on the side of this - that allows you put a clear tube on it

on the '95 you'll just have to pull the bowl to set it - do have reason to believe it is off?

Sort of a pain to do without pulling the carb -

Float level as measured by the book method:

26.95-28.95mm (1.06-1.114in)

IP Logged

jabman Senior Member Offline Posts: 411 England Gender:	Re: float hieght? Reply #5 - 03/05/10 at 11:14:24 same here could you poke a hose up the drain screw and use that
Back to top	93" savage, 177.5 main, 52.5 w/holes 3 turns out , middle circlip, 6" k&n round filter, Dyna muffler, TKAT brace IP Logged

seabeast77 YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 4	Re: float hieght? Reply #6 - 03/08/10 at 13:24:49 i'm sure it is off a little i just replaced it and it is running rich. and i even had a little gas come out of the overflows on the carb.
Back to top	IP Logged

jabman Senior Member Offline Posts: 411 England Gender:	Re: float hieght? Reply #7 - 03/08/10 at 13:32:14 im sure mine is too low hence weird large jets
Back to top	93" savage, 177.5 main, 52.5 w/holes 3 turns out , middle circlip, 6" k&n round filter, Dyna muffler, TKAT brace IP Logged

Phelonius Serious Thumper Offline SuzukiSavage.com Rocks! Posts: 1897	Re: float hieght? Reply #8 - 03/08/10 at 18:13:57 While the bowl is off, mo betta you swap out the four screws for stainless allens. They won't grow roots the way the factory anodized ones do. Phelonius
Back to top	Phelonius IP Logged

jabman Senior Member Offline Posts: 411 England Gender:	Re: float hieght? Reply #9 - 03/08/10 at 23:52:01 Phelonius wrote on 03/08/10 at 18:13:57: While the bowl is off, mo betta you swap out the four screws for stainless allens. They won't grow roots the way the factory anodized ones do. Phelonius +1
Back to top	93" savage, 177.5 main, 52.5 w/holes 3 turns out , middle circlip, 6" k&n round filter, Dyna muffler, TKAT brace IP Logged

seabeast77 YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 4	Re: float hieght? Reply #10 - 03/15/10 at 13:10:59 thanks for all the help guys. i have adjusted it but it seems like it may be a little to low now. oh well i will try it one more time .if it is not the float then i am perplexed. because now it is not starting easily like it hase no fuel and the idle is uneven.
Back to top	IP Logged

Pages: 1

‹ Previous topic | Next topic ›

« Home