Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› float hieght?
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages: 1
float hieght? (Read 137 times)
seabeast77
YaBB Newbies
Offline
SuzukiSavage.com
Rocks!
Posts: 4
float hieght?
03/04/10 at 21:05:57
does anyone know the best float hieght for 1995 savage? and what is the easiest way to adjust and measure it? thanks for the info guys.
Back to top
IP Logged
verslagen1
YaBB Moderator
ModSquad
Offline
Where there's a
will, I want to be
in it.
Posts: 28886
L.A. California
Gender:
Re: float hieght?
Reply #1 -
03/04/10 at 21:36:37
take a clear hose
run it from the bottom of the carb
up along the side
and open the drain valve
gas should come up a bit
now turn the petcock to prime
gas should come up to the gasket on the bowl
Back to top
Versey's Place
Tech Section Index
IP Logged
jabman
Senior Member
Offline
Posts: 411
England
Gender:
Re: float hieght?
Reply #2 -
03/05/10 at 02:55:13
cool i need to do this where do you fit the tube? i cannot find any hole
Back to top
93" savage, 177.5 main, 52.5 w/holes 3 turns out , middle circlip, 6" k&n round filter, Dyna muffler, TKAT brace
IP Logged
justin_o_guy2
Serious Thumper
Offline
What happened?
Posts: 55279
East Texas, 1/2 dallas/la.
Re: float hieght?
Reply #3 -
03/05/10 at 03:31:27
bottom of the bowl, little hang down with a screw poked in the side.
Back to top
The people never give up their liberties but under some delusion.- Edmund Burke.
IP Logged
Reelthing
Serious Thumper
Alliance Member
Offline
Fish or ride that is
the question
Posts: 5397
Houston,Tx
Gender:
Re: float hieght?
Reply #4 -
03/05/10 at 10:18:08
if that '95 is like mine it doesn't have a drain other than to remove the entire screw on the bottom - no place for the hose
unlike the '02 where the bottom of the bowl has a molded metal tube and the drain screw is on the side of this - that allows you put a clear tube on it
on the '95 you'll just have to pull the bowl to set it - do have reason to believe it is off?
Sort of a pain to do without pulling the carb -
Float level as measured by the book method:
26.95-28.95mm (1.06-1.114in)
Back to top
IP Logged
jabman
Senior Member
Offline
Posts: 411
England
Gender:
Re: float hieght?
Reply #5 -
03/05/10 at 11:14:24
same here could you poke a hose up the drain screw and use that
Back to top
93" savage, 177.5 main, 52.5 w/holes 3 turns out , middle circlip, 6" k&n round filter, Dyna muffler, TKAT brace
IP Logged
seabeast77
YaBB Newbies
Offline
SuzukiSavage.com
Rocks!
Posts: 4
Re: float hieght?
Reply #6 -
03/08/10 at 13:24:49
i'm sure it is off a little i just replaced it and it is running rich. and i even had a little gas come out of the overflows on the carb.
Back to top
IP Logged
jabman
Senior Member
Offline
Posts: 411
England
Gender:
Re: float hieght?
Reply #7 -
03/08/10 at 13:32:14
im sure mine is too low hence weird large jets
Back to top
93" savage, 177.5 main, 52.5 w/holes 3 turns out , middle circlip, 6" k&n round filter, Dyna muffler, TKAT brace
IP Logged
Phelonius
Serious Thumper
Offline
SuzukiSavage.com
Rocks!
Posts: 1897
Re: float hieght?
Reply #8 -
03/08/10 at 18:13:57
While the bowl is off, mo betta you swap out the four screws for stainless allens. They won't grow roots the way the factory anodized ones do.
Phelonius
Back to top
Phelonius
IP Logged
jabman
Senior Member
Offline
Posts: 411
England
Gender:
Re: float hieght?
Reply #9 -
03/08/10 at 23:52:01
Phelonius wrote
on 03/08/10 at 18:13:57:
While the bowl is off, mo betta you swap out the four screws for stainless allens. They won't grow roots the way the factory anodized ones do.
Phelonius
+1
Back to top
93" savage, 177.5 main, 52.5 w/holes 3 turns out , middle circlip, 6" k&n round filter, Dyna muffler, TKAT brace
IP Logged
seabeast77
YaBB Newbies
Offline
SuzukiSavage.com
Rocks!
Posts: 4
Re: float hieght?
Reply #10 -
03/15/10 at 13:10:59
thanks for all the help guys. i have adjusted it but it seems like it may be a little to low now. oh well i will try it one more time .if it is not the float then i am perplexed. because now it is not starting easily like it hase no fuel and the idle is uneven.
Back to top
IP Logged
Pages: 1
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
09/30/24 at 12:26:53
›
General Category
›
Rubber Side Down!
› float hieght?
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.