SuzukiSavage.com - turn signal project

Welcome, Guest. Please Login or Register :: View Members

SuzukiSavage.com › General Category › Rubber Side Down! › turn signal project

(Moderators: verslagen1, Dave, Serowbot)

‹ Previous topic | Next topic ›

Pages: 1

turn signal project (Read 210 times)

WebsterMark

Serious Thumper

Offline

SuzukiSavage.com
Rocks!

Posts: 13113

Gender: male

turn signal project
09/05/09 at 05:53:45

Gonna rain for the next two darn days here in St. Louis so I figured this would be a good time to do a project I’ve wanted to do on my ’07. I want to take off the stock turn signals, pivot the holder around the fork tubes 90 degrees and use the opening in the holder (now facing to the front) and install some small bulbs recessed inside as turn signals. Then I’ll find an amber lens cover to install. First question; how do I get the rubber cone off once I’ve removed the fake chrome turn signal housing?

IP Logged

PTRider Senior Member Offline Posts: 397	Re: turn signal project Reply #1 - 09/05/09 at 06:52:32 Will they be bright enough so a driver that cares just a little bit can see you?
Back to top	IP Logged

WebsterMark Serious Thumper Offline SuzukiSavage.com Rocks! Posts: 13113 Gender:	Re: turn signal project Reply #2 - 09/05/09 at 06:54:37 not sure, might have to use led light.
Back to top	IP Logged

WebsterMark Serious Thumper Offline SuzukiSavage.com Rocks! Posts: 13113 Gender:	Re: turn signal project Reply #3 - 09/06/09 at 07:18:06 Again, can anyone help with this? Is there an easy way to get the rubber cone off that sits under the turn signal without cutting it?
Back to top	IP Logged

prechermike Serious Thumper Alliance Member Offline Kalashna Kitty, from Skat Posts: 1190 Ponzer, NC Gender:	Re: turn signal project Reply #4 - 09/06/09 at 09:31:13 If I understand your plans, the wires run through the rubber things. You will have to take the eires completely out, then it is just a matter of a screw or two. But that is off the top of my head.
Back to top	2006, HD pipe, Tkat fork brace, elkhide handgrips, gel seat w/riser, silverblue, Ed L's forward controls, Wristwatch, biblethumper650@gmail.com IP Logged

SimonTuffGuy Serious Thumper Alliance Member Offline i like to thump... ;) Posts: 1159 Central PA Gender:	Re: turn signal project Reply #5 - 09/07/09 at 06:51:56 I think it's held on by a little screw on the inside of the mount. I'm looking at going with a set of these:
Back to top	Simon Pimptiva.com IP Logged

WebsterMark Serious Thumper Offline SuzukiSavage.com Rocks! Posts: 13113 Gender:	Re: turn signal project Reply #6 - 09/08/09 at 10:26:32 Those would be perfect. Let me know if you find them.
Back to top	IP Logged

SimonTuffGuy Serious Thumper Alliance Member Offline i like to thump... ;) Posts: 1159 Central PA Gender:	Re: turn signal project Reply #7 - 09/08/09 at 11:34:04 The site is: http://www.ledbikelights.net/products.htm If you order, let him know that I (SimonTuffGuy) sent you. He's a member over on another forum that I'm on. I'm going to order the tail light/turn signal combo for my fender, those signals, and a license plate light from him shortly.
Back to top	Simon Pimptiva.com IP Logged

buttgoat1 Serious Thumper Offline SuzukiSavage.com Rocks! Posts: 1042	Re: turn signal project Reply #8 - 09/09/09 at 09:57:30 I have been eyeing the LED lights myself, but I had already bought a pair of turn signals to replace my broken stockers. I cut a piece of aluminum angle and bolted it crossways above the license plate. Not the prettiest job in the world, but it worked. just need some extra $ to get the LEDS.
Back to top	IP Logged

Pages: 1

‹ Previous topic | Next topic ›

« Home