Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› Type of Inline Fuel filter and Petcock needed
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages:
1
2
Type of Inline Fuel filter and Petcock needed (Read 281 times)
marine5317
Full Member
Alliance Member
Offline
SuzukiSavage.com
Rocks!
Posts: 181
Lecanto,FL
Gender:
Re: Type of Inline Fuel filter and Petcock needed
Reply #15 -
04/06/09 at 18:34:09
I got this one at a cycle shop. It is clear with a bronze filter inside It has a 90% on thr bottom and I used -
1/4 ID fuel hose. Has been on over 1,000 miles and works fine.
Around $5.00
Ride Safe
Marine 5317
Back to top
«
Last Edit: 04/07/09 at 10:52:19 by marine5317
»
IP Logged
verslagen1
YaBB Moderator
ModSquad
Offline
Where there's a
will, I want to be
in it.
Posts: 28886
L.A. California
Gender:
Re: Type of Inline Fuel filter and Petcock needed
Reply #16 -
04/06/09 at 22:13:50
SavageDanny wrote
on 04/06/09 at 09:54:10:
Going to have to put that on my wish list then. I did have the technique for getting the tank on and off down. However the last time I wrestled with it I got so angry I let loose a series of
profanity that drove my wife to locking me in the garage until I promised to calm down
. Don't really want to do a repeat of that event.
Is there any modification needed for the swap or is it fairly direct?
I think that was a benefit that would lasted till about midnight... every nite
Back to top
Versey's Place
Tech Section Index
IP Logged
prechermike
Serious Thumper
Alliance Member
Offline
Kalashna Kitty, from
Skat
Posts: 1190
Ponzer, NC
Gender:
Re: Type of Inline Fuel filter and Petcock needed
Reply #17 -
04/07/09 at 13:09:33
Arthur wrote
on 04/06/09 at 15:42:39:
Here is what I did:
2. Added an inline fuel shut off valve ( I leave the Savage petcock on.)
Gort, I was wondering why you added a fuel valve instead of using the one on the petcock?
Back to top
2006, HD pipe, Tkat fork brace, elkhide handgrips, gel seat w/riser, silverblue, Ed L's forward controls, Wristwatch, biblethumper650@gmail.com
IP Logged
Gort
Ex Member
Re: Type of Inline Fuel filter and Petcock needed
Reply #18 -
04/07/09 at 13:40:34
I converted the Savage petcock according to the instructions in the tech section, so as to eliminate the vacuum feature. While the vacuum design causes the fuel to shut off if the engine stops, the diaphragm will crack with age and use, and shut the engine down when you are riding. When you disassemble the Savage petcock, you will see that it has an O ring which will wear and fail with age and use, as well. Also, the innards are not that sturdy. So, I decided to leave the petcock turned on and instead install a much heavier duty ballcock shut off valve. I don't want to get halfway across the US or into Canada only to have some component failure and then hope that I can get the part somewhere, if at all.
Back to top
IP Logged
Seth C.
Full Member
Offline
Posts: 173
Tucson, AZ
Gender:
Re: Type of Inline Fuel filter and Petcock needed
Reply #19 -
04/07/09 at 13:46:21
If installing the raptor petcock, what is the best way to seal the vacuum on the carb?
Back to top
2001 Suzuki Savage LS650
IP Logged
Gort
Ex Member
Re: Type of Inline Fuel filter and Petcock needed
Reply #20 -
04/07/09 at 13:55:09
Many will use the rubber vacuum caps you can buy at the auto parts stores. I don't like them because I've had them dry out, crack and leak with age. Instead, I shortened the Savage vacuum line and screwed a tight fitting machine screw into the end of the vacuum line. I first coated the threads with a very thin coat of Permatex Copper gasket sealant, but only on the upper half of the screw, and under the screw head. Then I let it set 24hrs. before starting the engine.
Back to top
IP Logged
Seth C.
Full Member
Offline
Posts: 173
Tucson, AZ
Gender:
Re: Type of Inline Fuel filter and Petcock needed
Reply #21 -
04/07/09 at 14:02:08
Arthur wrote
on 04/07/09 at 13:55:09:
Many will use the rubber vacuum caps you can buy at the auto parts stores. I don't like them because I've had them dry out, crack and leak with age. Instead, I shortened the Savage vacuum line and screwed a tight fitting machine screw into the end of the vacuum line. I first coated the threads with a very thin coat of Permatex Copper gasket sealant, but only on the upper half of the screw, and under the screw head. Then I let it set 24hrs. before starting the engine.
Nice!
Back to top
2001 Suzuki Savage LS650
IP Logged
Pages:
1
2
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
09/28/24 at 08:36:41
›
General Category
›
Rubber Side Down!
› Type of Inline Fuel filter and Petcock needed
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.