SuzukiSavage.com - Exaust header specs

Welcome, Guest. Please Login or Register :: View Members

SuzukiSavage.com › General Category › Rubber Side Down! › Exaust header specs

(Moderators: verslagen1, Dave, Serowbot)

‹ Previous topic | Next topic ›

Pages: 1

Exaust header specs (Read 100 times)

AngloSaxon Full Member Offline I'd rather have one big one than four small ones. Posts: 141 Framingham MA Gender:	Exaust header specs 01/28/09 at 06:17:22 Does anyone know the header diameter off hand?
Back to top	As yet, a Bog Standard '87 with a big arse Harley muffler. IP Logged

odvelasc Ex Member	Re: Exaust header specs Reply #1 - 01/28/09 at 10:46:26 yeah, its " a headache" lol. Mine has three different tiers lol
Back to top	IP Logged

odvelasc Ex Member	Re: Exaust header specs Reply #2 - 01/28/09 at 10:49:35 by a cheap caliper and measure it. Or simple math. Measure the diameter and multiply by Pi (3.14). Tada C=dxpi
Back to top	IP Logged

verslagen1

YaBB Moderator
ModSquad

Offline

Where there's a
will, I want to be
in it.

Posts: 28884
L.A. California
Gender: male

Re: Exaust header specs
Reply #3 - 01/28/09 at 11:14:55

odvelasc wrote on 01/28/09 at 10:49:35:

by a cheap caliper and measure it. Or simple math. Measure the diameter and multiply by Pi (3.14). Tada

C=dxpi

err, you left out a couple of... important words, like circumference.

So if you use a tape rule to measure the circumference...
divide by pi and you'll have the diameter of the pipe.

Versey's Place
Tech Section Index

IP Logged

odvelasc

Ex Member

Re: Exaust header specs
Reply #4 - 01/28/09 at 11:29:41

verslagen1 wrote on 01/28/09 at 11:14:55:

odvelasc wrote on 01/28/09 at 10:49:35:

by a cheap caliper and measure it. Or simple math. Measure the diameter and multiply by Pi (3.14). Tada

C=dxpi

err, you left out a couple of... important words, like circumference.

So if you use a tape rule to measure the circumference...
divide by pi and you'll have the diameter of the pipe.

you are right. I gave him the formula for circumference. The diameter can just be measured with a tape measure.

IP Logged

verslagen1

YaBB Moderator
ModSquad

Offline

Where there's a
will, I want to be
in it.

Posts: 28884
L.A. California
Gender: male

Re: Exaust header specs
Reply #5 - 01/28/09 at 13:01:33

odvelasc wrote on 01/28/09 at 11:29:41:

verslagen1 wrote on 01/28/09 at 11:14:55:

odvelasc wrote on 01/28/09 at 10:49:35:

by a cheap caliper and measure it. Or simple math. Measure the diameter and multiply by Pi (3.14). Tada

C=dxpi

err, you left out a couple of... important words, like circumference.

So if you use a tape rule to measure the circumference...
divide by pi and you'll have the diameter of the pipe.

you are right. I gave him the formula for circumference. The diameter can just be measured with a tape measure.

AWE JUST SHOOT ME FOR CRYING OUT LOUD!

Versey's Place
Tech Section Index

IP Logged

odvelasc

Ex Member

Re: Exaust header specs
Reply #6 - 01/28/09 at 17:09:55

verslagen1 wrote on 01/28/09 at 13:01:33:

odvelasc wrote on 01/28/09 at 11:29:41:

verslagen1 wrote on 01/28/09 at 11:14:55:

odvelasc wrote on 01/28/09 at 10:49:35:

by a cheap caliper and measure it. Or simple math. Measure the diameter and multiply by Pi (3.14). Tada

C=dxpi

err, you left out a couple of... important words, like circumference.

So if you use a tape rule to measure the circumference...
divide by pi and you'll have the diameter of the pipe.

you are right. I gave him the formula for circumference. The diameter can just be measured with a tape measure.

AWE JUST SHOOT ME FOR CRYING OUT LOUD!

Bang Bang!! Grin

IP Logged

LANCER Serious Thumper Alliance Member Offline Savage Beast Performance Parts Posts: 10661 Oklahoma Gender:	Re: Exaust header specs Reply #7 - 01/28/09 at 18:16:31 AngloSaxon wrote on 01/28/09 at 06:17:22: Does anyone know the header diameter off hand? Stock header ID is about 1.3"
Back to top	IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28884 L.A. California Gender:	Re: Exaust header specs Reply #8 - 01/28/09 at 18:28:28 The header is double wall. The outside wall is Ø2.000" The flange is Ø2.413" The flange is .403" thick The inside wall is Ø1.68" and tapers down probably 1.3" can't measure that far. Does that answer your question?
Back to top	Versey's Place Tech Section Index IP Logged

Pages: 1

‹ Previous topic | Next topic ›

« Home