Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› Drive pully Nut #$@%$#**
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages: 1
Drive pully Nut #$@%$#** (Read 133 times)
mick
Serious Thumper
Alliance Member
Offline
Hell-bound
Posts: 7323
Dayton Oregon
Gender:
Drive pully Nut #$@%$#**
11/09/08 at 14:24:59
Hi guys ,I'm having one heck of a job trying to get the drive pully nut off, I'm beginning to think it's LHT ,is it?
I have applied copius amounts of WD40 ,applied heat,all to no avail.
I'm going to have a late lunch and have one more go at it before I use a cold chisle. Any ideas guy's ?
Back to top
Science and Logic fly you to the moon,
Religion makes you fly into skyscrapers
IP Logged
88pagan
Full Member
Offline
God is just an
imaginary friend for
adults..
Posts: 237
Norco, California
Gender:
Re: Drive pully Nut #$@%$#**
Reply #1 -
11/09/08 at 14:32:40
I don't recall mine being that difficult to remove, maybe use an impact for removal? But..I believe it's right hand thread so maybe that's why it's not coming off.
Back to top
96 Bobber - Screamin Eagle, header wrap, K+N cone filter, jetted, straight bar w/1.5" risers, solo seat, Ed. L fwd ctrls, custom rear fender, TKat, Metallic charcoal and polished all over.
IP Logged
Yonuh Adisi FSO
Serious Thumper
Offline
Savage Jedi (Knight)
Posts: 3622
Pilot Valley NV, aka Tatooine
Gender:
Re: Drive pully Nut #$@%$#**
Reply #2 -
11/09/08 at 14:35:36
If you are talking about the forward pully that the belt goes around, it is standard righty tighty lefty loosey, I know because I just removed it a couple of days ago on the FireLizard.
Back to top
Check out Flight of Destiny
http://www.amazon.com/dp/B00H9130XC
IP Logged
rigidchop
Serious Thumper
Offline
don't feed the drama
llama
Posts: 1105
ravenswood wv
Gender:
Re: Drive pully Nut #$@%$#**
Reply #3 -
11/09/08 at 16:45:20
i had a heck of a time getting mine off. ended up bending a spoke and breaking the rear pulley. good times.
Back to top
87 VM ED L
IP Logged
mick
Serious Thumper
Alliance Member
Offline
Hell-bound
Posts: 7323
Dayton Oregon
Gender:
Re: Drive pully Nut ,It's off,new problem
Reply #4 -
11/09/08 at 17:14:20
Ok I got the bloody thing off, I used an 1 1/4 " socket with a 18" breaker bar and a 3 foot exstention steel tube,and my brother in law on the rear brake.
Now the next trick is getting the engine out,wires are all disconected,
engine bolts all out,it moves freely,but I gotta rest up and have some wheaties before trying to lift that bugger out,maybe some thin rope around the jug, any one out there know the trick to it?
I would rather use finess than brute force seeing I have more of the former,and less of the later.
Back to top
Science and Logic fly you to the moon,
Religion makes you fly into skyscrapers
IP Logged
88pagan
Full Member
Offline
God is just an
imaginary friend for
adults..
Posts: 237
Norco, California
Gender:
Re: Drive pully Nut #$@%$#**
Reply #5 -
11/09/08 at 17:19:56
No real tricks to offer from here. Pulling my engine out went very easily and very quickly. Putting it back in and getting the bolts through while moving the engine around proved to be a bit more difficult. I already had the head and head cover off when I pulled the engine, don't know if that's what made it so much easier.
Back to top
96 Bobber - Screamin Eagle, header wrap, K+N cone filter, jetted, straight bar w/1.5" risers, solo seat, Ed. L fwd ctrls, custom rear fender, TKat, Metallic charcoal and polished all over.
IP Logged
mick
Serious Thumper
Alliance Member
Offline
Hell-bound
Posts: 7323
Dayton Oregon
Gender:
Re: Drive pully Nut #$@%$#**
Reply #6 -
11/09/08 at 19:19:03
88pagan wrote
on 11/09/08 at 17:19:56:
No real tricks to offer from here. Pulling my engine out went very easily and very quickly. Putting it back in and getting the bolts through while moving the engine around proved to be a bit more difficult. I already had the head and head cover off when I pulled the engine, don't know if that's what made it so much easier.
Well dang, I only wanted to take the head off to do a valve job,but in the clymer manual it says you cant get the head off without taking the engine out. I have all the bolts out of the head cover but it aint moving
eather, and that is something I don't want to use a hammer on.
I will study the book some more and have a go in the morning.
Back to top
Science and Logic fly you to the moon,
Religion makes you fly into skyscrapers
IP Logged
T Mack 1 - FSO
Serious Thumper
Alliance Member
Offline
sold 2001 LS650 for
a 1986 XLH1100
Posts: 2919
Emmaus,Pa
Gender:
Re: Drive pully Nut #$@%$#**
Reply #7 -
11/10/08 at 09:46:21
Mick,
You didn't say so I have to ask.
Did you bend down the tab of the locking washer when you were trying to remove the nut??? Without it bent down, you would have a real real real hard time getting the nut off.
Back to top
Engineers design things, Technicians make them work.
---
30% of being mechanical is confidence/30% is knowing to go slow when needed/30% is looking repeatedly at what you have/10% is dumb luck
IP Logged
beck
YaBB Newbies
Offline
SuzukiSavage.com
Rocks!
Posts: 21
Re: Drive pully Nut ,It's off,new problem
Reply #8 -
11/10/08 at 13:06:20
mick wrote
on 11/09/08 at 17:14:20:
Now the next trick is getting the engine out,wires are all disconected,
engine bolts all out,it moves freely,but I gotta rest up and have some wheaties before trying to lift that bugger out,maybe some thin rope around the jug, any one out there know the trick to it?
I would rather use finess than brute force seeing I have more of the former,and less of the later.
Here is a trick I used while building/rebuilding HD cycles. I used a large piece of foam that I had used for camping. A layer of blankets would probably work for this too. Take most of the bolts out, but leave the motor secure enough to lay the bike over on the padding. Take the rest of the bolts out after padding under the motor or frame as needed. The motor and frame are then 2 pieces on the padding. Set the frame up and the motor is out. Just reverse the procedure to put the motor back in. Hope this helps.
Back to top
IP Logged
mick
Serious Thumper
Alliance Member
Offline
Hell-bound
Posts: 7323
Dayton Oregon
Gender:
Re: Drive pully Nut #$@%$#**
Reply #9 -
11/10/08 at 13:41:42
T Mack 1 - FSO wrote
on 11/10/08 at 09:46:21:
Mick,
You didn't say so I have to ask.
Did you bend down the tab of the locking washer when you were trying to remove the nut??? Without it bent down, you would have a real real real hard time getting the nut off.
Yes I did,I read that in the manuel.
Back to top
Science and Logic fly you to the moon,
Religion makes you fly into skyscrapers
IP Logged
mick
Serious Thumper
Alliance Member
Offline
Hell-bound
Posts: 7323
Dayton Oregon
Gender:
Re: Drive pully Nut ,It's off,new problem
Reply #10 -
11/10/08 at 13:46:59
beck wrote
on 11/10/08 at 13:06:20:
mick wrote
on 11/09/08 at 17:14:20:
Now the next trick is getting the engine out,wires are all disconected,
engine bolts all out,it moves freely,but I gotta rest up and have some wheaties before trying to lift that bugger out,maybe some thin rope around the jug, any one out there know the trick to it?
I would rather use finess than brute force seeing I have more of the former,and less of the later.
Here is a trick I used while building/rebuilding HD cycles. I used a large piece of foam that I had used for camping. A layer of blankets would probably work for this too. Take most of the bolts out, but leave the motor secure enough to lay the bike over on the padding. Take the rest of the bolts out after padding under the motor or frame as needed. The motor and frame are then 2 pieces on the padding. Set the frame up and the motor is out. Just reverse the procedure to put the motor back in. Hope this helps.
A very good idea Beck ,the problem there is, space, not enough room to lay it down,I cant back it out into the main building because there is a huge hoist just outside the door,and that will be there until my B/in law finishes his project, ( about two months)
Back to top
Science and Logic fly you to the moon,
Religion makes you fly into skyscrapers
IP Logged
verslagen1
YaBB Moderator
ModSquad
Offline
Where there's a
will, I want to be
in it.
Posts: 28884
L.A. California
Gender:
Re: Drive pully Nut ,It's off,new problem
Reply #11 -
11/10/08 at 13:59:31
beck wrote
on 11/10/08 at 13:06:20:
Here is a trick I used while building/rebuilding HD cycles. I used a large piece of foam that I had used for camping. A layer of blankets would probably work for this too. Take most of the bolts out, but leave the motor secure enough to lay the bike over on the padding. Take the rest of the bolts out after padding under the motor or frame as needed. The motor and frame are then 2 pieces on the padding. Set the frame up and the motor is out. Just reverse the procedure to put the motor back in. Hope this helps.
Great idea beck, my back thanks you.
must be awfull to have to work in a closet.
Take all that you can take off, then claim bad back and get your brother to lift it out for you
Back to top
Versey's Place
Tech Section Index
IP Logged
Pages: 1
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
09/25/24 at 06:26:52
›
General Category
›
Rubber Side Down!
› Drive pully Nut #$@%$#**
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.