SuzukiSavage.com - Good Grief!!!!

grim

Junior Member

Offline

Posts: 92
San Jose,CA
Gender: male

Good Grief!!!!
03/26/07 at 21:35:20

I have been pulling on the top half of the cylinder head and cannot get it off..(while the engine is mounted on the frame!). That one back right bolt is way too long. I saw one of you did this...HOW??? Do I really have to remove the engine? Such a pain and wasted night.....

And I WILL be able to put the cam chain back with no marks, Correct? The chain just fell down to the bottom...?

Thanks all

Back to top

IP Logged

justin_o_guy

Ex Member

Re: Good Grief!!!!
Reply #1 - 03/26/07 at 21:44:34

Now that the chain is laying down, the cam & crank have no idea where the other is. All ya gotta do is, pop the head off, bring the piston to the top lining up the marks inside th left cover, when the head goes back on, just line the cam marks up according to the instructions & Voila, it oughta be timed. All this according to a guy who JUST could be wrong. Folks? Am I? Remember, while you have all this stuff apart, it may be a good idea to tweak the rear cam chain guide, so as to keep the tensioner in further.This is a new thing being tried & is unproven over the long haul, but seems reasonable that it would work.

Back to top

IP Logged

verslagen1

YaBB Moderator
ModSquad

Offline

Where there's a
will, I want to be
in it.

Posts: 28905
L.A. California
Gender: male

Re: Good Grief!!!!
Reply #2 - 03/26/07 at 23:18:47

Grim, some frames are too small to get the head off without removing the engine.

You might try to remove the engine mounting screws and let the engine sag and try again. Or rocking it to one side to get that screw. Just a thought, haven't done it myself. Give me a couple weeks, I might need to know from you.

Purpose for removing head? If it was just a look see. Might be easier to just put it back together if you don't want to fight it.

I don't know if the counter balence has a particular timing with the firing order, but I don't think it does. should be easy to put back together align the timing marks as stated by justin and shown in the manuals.

Back to top

Versey's Place
Tech Section Index

IP Logged

barry68v10 Serious Thumper Offline Posts: 955 Maryland Gender:	Re: Good Grief!!!! Reply #3 - 03/27/07 at 03:50:06 Don't know if this will save you time in the long run, but you don't need to take the head off to find TDC. You can remove the plug and put a wooden dowel rod in the hole to find TDC. Just make sure the engine is on the correct stroke, not 360 degrees out.
Back to top	petc0ck mod, white spacer removed, 150 main jet, 12.5" shocks, 16" turnout muff, oil cooler mod, chain conversion, Tkat brace, external fuel filter, fuel screen removed... IP Logged

justin_o_guy Ex Member	Re: Good Grief!!!! Reply #4 - 03/27/07 at 06:48:17 I thought since the thing fires at the top of every stroke it wouldn't matter about the piston, just put it at TDC & set the cam in it at TDC compression & that's it/.
Back to top	IP Logged

grim

Junior Member

Offline

Posts: 92
San Jose,CA
Gender: male

Re: Good Grief!!!!
Reply #5 - 03/27/07 at 07:01:00

Removing head and cylinder to replace the bottom and middle gaskets. I had a leak, and so just replacing.....everything. I did find my cam chain tensioner had no spring action. That was a good find. The spring was cut short.

The pain-in-the-butt bolt is about 1cm too long. Will just remove engine. Any suggestions while I am this far in the engine?

Back to top

IP Logged

justin_o_guy

Ex Member

Re: Good Grief!!!!
Reply #6 - 03/27/07 at 07:13:52

Well, Maybe a few mods? Ther's talk of a fatter piston & then theres the hardening of the bore that,, Lancer? has on his to get max life & minimum friction. Seems that if a guy did those he could go to the chain & get the high speed RPM's down to a comfortable spot & still keep the bottom end performance up, Specially if the cam got replaced & the carb/exhaust tuning was good. Darn shame to be doin all this now.

This IS an opportunity to get figured oiut how to get iin & out of the engine so IF you decide to do those mods, you can do it with minimum downtime.

Back to top

IP Logged

barb36jack31 Full Member 2005 No Login Offline I love YaBB 1G - SP1! Posts: 173 Heathrow, FL Gender:	Re: Good Grief!!!! Reply #7 - 03/28/07 at 05:41:49 Saw a post here stating that the engine fires at the top of each stroke. Is that correct? And if so, how come? Jack H.
Back to top	05 S40 , air needle adjustment, white spacer, 152.5 main jet, K&N filter, SuperTrapp muffler, Progressive shocks , sissy bar off IP Logged

verslagen1 YaBB Moderator ModSquad Offline Where there's a will, I want to be in it. Posts: 28905 L.A. California Gender:	Re: Good Grief!!!! Reply #8 - 03/28/07 at 07:03:36 It does fire every TDC, the reason was posted not too long ago. One of the Cam chain threads I believe.
Back to top	Versey's Place Tech Section Index IP Logged