Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› Drag bars - are taller risers needed?
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages: 1
Drag bars - are taller risers needed? (Read 8 times)
r-tru-d2
YaBB Newbies
Offline
Posts: 26
Greenville, IL
Gender:
Drag bars - are taller risers needed?
02/23/07 at 14:21:45
I'm going to outfit my wife's Savage with a set of drag bars. I was wondering if taller risers are necessary to keep the bars from hitting the tank. I'm looking at about 4" pullback drag bars, probably 26-28 inches wide. Of course, once I have them installed, I might go ahead and order pullback risers if she has trouble reaching them.
Any thoughts?
Back to top
IP Logged
Savage_Rob
Serious Thumper
Alliance Member
Offline
Mechanically
Inclined Amateur
Posts: 6972
Texas (Dallas area)
Gender:
Re: Drag bars - are taller risers needed?
Reply #1 -
02/23/07 at 14:36:24
It depends what you are replacing. The early LS650 Savages with flat bars had taller riser/clamps than those on my 98 with buckhorns. I believe the LS650 S40s have different ones also. I can only relate my experience. Going from an LS650 with buckhorns to drag bars required risers to keep from hitting the tank. I used risers with a very slight pullback and I like them a lot. One note: some LS650s (usually those with buckhorns) have a master cylinder with the brake line's banjo fitting on the left side. If this is your situation, be careful of the width of your bars so that you have room. When I first tried the small flat bars from an 86 Savage, it did not work well. With my 36" drag bars, it's no problem.
Back to top
1998|MAC muffler|ceramic coated header|K&N air filter|Amal Mk2 carb|Odyssey battery|iridium plug|NC windshield|Dunlop 491s|Superbrace|EBC brake rotor|12.5" Progressive shocks|Kuryakyn ISO grips
IP Logged
r-tru-d2
YaBB Newbies
Offline
Posts: 26
Greenville, IL
Gender:
Re: Drag bars - are taller risers needed?
Reply #2 -
02/23/07 at 14:41:16
Thanks. It's a 1987 with short risers and buckhorns. I'm looking at maybe some Deuce style 6" risers with 1.5" pullback, and 28" bars with 4" pullback. I'll take a look at the master cylinder to see what you're talking about.
Back to top
IP Logged
Savage_Rob
Serious Thumper
Alliance Member
Offline
Mechanically
Inclined Amateur
Posts: 6972
Texas (Dallas area)
Gender:
Re: Drag bars - are taller risers needed?
Reply #3 -
02/23/07 at 17:33:40
This thread
has some pics of my bike as she was then when I tried the old flat bars. You can see the riser/master cylinder interference. The risers Lancer mentions are the set I bought and I like them a lot.
This thread
has some pics of the 36" bars I have on her now.
Back to top
1998|MAC muffler|ceramic coated header|K&N air filter|Amal Mk2 carb|Odyssey battery|iridium plug|NC windshield|Dunlop 491s|Superbrace|EBC brake rotor|12.5" Progressive shocks|Kuryakyn ISO grips
IP Logged
amcline
Ex Member
Re: Drag bars - are taller risers needed?
Reply #4 -
03/01/07 at 09:51:26
is there a riser thats only about 1-2" higher than a stock 96-buckhorn riser? i like my new short drag bars but it hits the tank at lock, both ways, and dont want any pull back, only have 4" or so on the bars...
Back to top
IP Logged
Salad_Shaker
Ex Member
Re: Drag bars - are taller risers needed?
Reply #5 -
03/01/07 at 12:02:39
Just fitted some e-bay bargain black Harley Sporster standard bars - not quite drag, not quite buckhorn to The Lettuce. They just clear the tank on full lock without adding anything to the std yoke.
The idea was to pitch me forward a shade a get a little weight off my tailbone. It seems to work.
Back to top
IP Logged
Pages: 1
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
09/19/24 at 23:39:47
›
General Category
›
Rubber Side Down!
› Drag bars - are taller risers needed?
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.