Home
Forum
Search
Login
Register
Merch
Donate
Welcome, Guest. Please
Login
or
Register
::
View Members
SuzukiSavage.com
›
General Category
›
Rubber Side Down!
› Tuning Edelbrock Quiksilver Carb
(Moderators:
verslagen1
,
Dave
,
Serowbot
)
‹
Previous topic
|
Next topic
›
Pages:
1
2
Tuning Edelbrock Quiksilver Carb (Read 28 times)
Yellow96
Junior Member
Offline
Posts: 67
Re: Tuning Edelbrock Quiksilver Carb
Reply #15 -
02/21/07 at 22:00:25
Did you have to replace the intake hose on the filter side? After taking it apart and back together again I noticed that the hose doesn't reach or fit over the stock airbox outlet. Looks like the hose should be the same diameter on both ends, but the stock one is smaller on one end. The small end probably used to go on the carb but it doesn't fit the Edelbrock. Anyway it is just turned backwards and the big end fits the carb with the smaller end pretty tight but not perfectly sealed on the airbox.
Back to top
IP Logged
Savage_Rob
Serious Thumper
Alliance Member
Offline
Mechanically
Inclined Amateur
Posts: 6972
Texas (Dallas area)
Gender:
Re: Tuning Edelbrock Quiksilver Carb
Reply #16 -
02/22/07 at 05:36:54
Yellow96 wrote
on 12/31/69 at 16:00:02:
Did you have to replace the intake hose on the filter side? After taking it apart and back together again I noticed that the hose doesn't reach or fit over the stock airbox outlet. Looks like the hose should be the same diameter on both ends, but the stock one is smaller on one end. The small end probably used to go on the carb but it doesn't fit the Edelbrock. Anyway it is just turned backwards and the big end fits the carb with the smaller end pretty tight but not perfectly sealed on the airbox.
I think a lot of folks who change carbs use a pod/cone filter instead of the airbox. I have an Amal Mk2 carb and I bought some flexible ducting (made to replace A/C ducting in cars) from Autozone and it works perfectly.
Back to top
1998|MAC muffler|ceramic coated header|K&N air filter|Amal Mk2 carb|Odyssey battery|iridium plug|NC windshield|Dunlop 491s|Superbrace|EBC brake rotor|12.5" Progressive shocks|Kuryakyn ISO grips
IP Logged
Yellow96
Junior Member
Offline
Posts: 67
Re: Tuning Edelbrock Quiksilver Carb
Reply #17 -
02/22/07 at 11:40:20
Ok, frustration is setting in now.
Here's how I installed the new needle:
Installed in the slide over spring
Installed needle adjuster pin, threaded side up
Installed the adjuster screw assembly
Turned center screw right until it stopped
Turned center screw left 14 clicks
Bumped up the idle to be sure it was over 1000 RPM
Started adjusting from there. Never could get a good start and run. It will start with the choke on but then when I start to turn the choke off, it revs up and then dies. I tried all the way lean and all the way rich with similar results. Also started at full rich and bracketted it down 3 or 4 clicks at a time, no dice. Not sure what's up here, any thoughts?
The old setup had the vaccuum line from the carb to the petc0ck disconected and plugged and the valve in PRI all of the time. Not sure if that matters or not.
Back to top
IP Logged
Yellow96
Junior Member
Offline
Posts: 67
Re: Tuning Edelbrock Quiksilver Carb
Reply #18 -
02/22/07 at 14:25:12
I put the 6-K back in today and is starts and runs fine with the exception of being too rich at wide open. I was able to tune all of the backfire out but had to go to full rich on the idle mixture to do it. I'm thinking of trying a 5-K or E, do you think it will matter?
Maybe this is a problem of filter, carb, muffler combo?
The only other thing I can think of is that this carb can't run on an O needle which is designed for street carbs. E and Ks are used on ATV carbs.
Back to top
IP Logged
Pages:
1
2
‹
Previous topic
|
Next topic
›
Forum Jump »
» 10 most recent posts
» 10 most recent topics
General Category
»» Rubber Side Down!
- Technical Documents/Reference
- The Marketplace
- The Cafe
- Politics, Religion (Tall Table)
- Forum Upgrade Issues / Tests
« Home
« Home
SuzukiSavage.com
09/19/24 at 19:49:20
›
General Category
›
Rubber Side Down!
› Tuning Edelbrock Quiksilver Carb
SuzukiSavage.com
» Powered by
YaBB 2.2
!
YaBB
© 2000-2007. All Rights Reserved.