SuzukiSavage.com - Suzuki/Clymer Manual Errors

Welcome, Guest. Please Login or Register :: View Members

SuzukiSavage.com › General Category › Technical Documents/Reference › Suzuki/Clymer Manual Errors

(Moderators: verslagen1, Dave, Serowbot)

‹ Previous topic | Next topic ›

Pages: 1 2

Suzuki/Clymer Manual Errors (Read 1876 times)

Digger Serious Thumper 2005 No Login Offline Ya gotta be tough to ride singles! Posts: 1604 Colorado Springs, CO Gender:	Re: Suzuki/Clymer Manual Errors Reply #15 - 08/22/13 at 19:05:49 Minor Clymer error, but an error nonetheless: Chapter 11 (Brakes), Front Caliper section, Caliper Rebuilding Procedure: Step #27 currently reads: Install the rubber boots (Figure 50) into the receptacles in the caliper bracket It SHOULD read: Install the rubber boots (Figure 50) into the receptacles in the caliper body
Back to top	« Last Edit: 11/09/13 at 18:44:42 by Digger » Digger 2001, Metallic Glacial Blue, Raptor Petcock, Verslavy (first hole) (otherwise, mechanically, the bike is stock), 13,xxx miles I don't own a cage. www.astronautbiker.com IP Logged

wambr Serious Thumper Offline SuzukiSavage.com Rocks! Posts: 610 Russia, Samara Gender:	Re: Suzuki/Clymer Manual Errors Reply #16 - 08/23/13 at 11:36:21 I think, it is appropriate to add that I found... guide maintenance and repair of Kawasaki recommends that you check the belt tension..
Back to top	11092.jpg Yeah, it's not bigtwin, but it is the best half of it IP Logged

wambr Serious Thumper Offline SuzukiSavage.com Rocks! Posts: 610 Russia, Samara Gender:	Re: Suzuki/Clymer Manual Errors Reply #17 - 08/23/13 at 11:59:02 I mean that many people ask about how to properly adjust the belt tension....(this is another options)
Back to top	Yeah, it's not bigtwin, but it is the best half of it IP Logged

Kris01 Serious Thumper Offline Eat, sleep, RIDE! Posts: 3767 Tennessee Gender:	Re: Suzuki/Clymer Manual Errors Reply #18 - 10/15/14 at 16:20:44 Page 343 - Staring system should read starting system
Back to top	There's no problem that a full tank of gas and a sunny day can't fix! 2008 S40, Rotella T 15W-40 w/ZDDP added, Dyna, 140/90-15, Battery Tender Jr., Seat lift, #52.5/150/3 washers, Raptor IP Logged

Jeff71 Senior Member Offline I'm a bike noob!!!!! Posts: 378 South of Chicago, the suburbs Gender:	Re: Suzuki/Clymer Manual Errors Reply #19 - 11/12/14 at 22:47:40 Look at the wiring on p.351 and 353. The B/W wire coming from the rear brake light switch connects to the wrong wire on the tail/brake light! Jeff
Back to top	Yeah, like I have any clue what is going on.... http://myrycabuild.weebly.com IP Logged

Drestakil Full Member Offline innocent bystander Posts: 178 Southern Illinois Gender:	Re: Suzuki/Clymer Manual Errors Reply #20 - 10/09/15 at 12:26:50 Pretty obvious but on page 59 #10 "rotate engine additional 180". It should read rotate 360 as it does on page 49 #9.
Back to top	IP Logged

RevJay YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 5	Re: Suzuki/Clymer Manual Errors Reply #21 - 04/04/17 at 07:30:30 Kropatchek wrote on 06/16/06 at 01:20:23: And another mistake: Pointed out to a Dutch Savage rider. The oilseals of the sliding members of the front suspension. Fit them face up instead of face down. That way the oil is kept in the struts. (will refer to the pages when I get home) Greetz Kropatchek ???
Back to top	IP Logged

RevJay YaBB Newbies Offline SuzukiSavage.com Rocks! Posts: 5	Re: Suzuki/Clymer Manual Errors Reply #22 - 04/04/17 at 07:35:29 Page 276 9b Position the seal with the open groove facing upward (pic) and slide oil seal (c) down onto the fork tube. I have never been instructed to do it this way surely the seal goes open groove down ?? Jay
Back to top	IP Logged

verslagen1

YaBB Moderator
ModSquad

Offline

Where there's a
will, I want to be
in it.

Posts: 28754
L.A. California
Gender: male

Re: Suzuki/Clymer Manual Errors
Reply #23 - 04/04/17 at 09:01:04

Our HowTo says...
slavy wrote on 10/24/05 at 23:11:37:

install the new seal the same way /MAKE SURE THE LETTERS AND NUMBERS ARE FACING UP/. Install the retaining clip and the dust seal.

This would make sense as the groove side of the seal is normally installed on the pressure side. This increases seal pressure during the time it's most likely to leak.

Versey's Place
Tech Section Index

IP Logged

YaBB Newbies

Offline

SuzukiSavage.com
Rocks!

Posts: 1
Crockett, CA USA
Gender: male

Re: Suzuki/Clymer Manual Errors
Reply #24 - 08/31/17 at 06:11:12

Front turn signals wiring errors...

On page 354 of the Clymer manual, the wire to the Left Front Turn Signal (bottom connection) is shown going to the wrong wire. It shows it going to GND instead of the turn signal switch BLACK wire.

The BLACK wire is instead shown going to the Right Turn Signal center connector which SHOULD be shown going to GND.

2013 with 4000 miles

IP Logged

Christof13T Full Member Offline SuzukiSavage.com Rocks! Posts: 211 Vicoria, Texas Gender:	Re: Suzuki/Clymer Manual Errors Reply #25 - 09/29/17 at 23:46:07 Page 15 General Information... Hammers (fig 37) is Ignition Gauge in the picture. Ignition gauge (fig 38) is Hammers in the picture. Wanted to make sure nobody got confused, that might get messy...
Back to top	IP Logged

Pages: 1 2

‹ Previous topic | Next topic ›

« Home