SuzukiSavage.com
/cgi-bin/YaBB.pl General Category >> Rubber Side Down! >> fix it so it brakes, ryca /cgi-bin/YaBB.pl?num=1561831516 Message started by Matchless G11 on 06/29/19 at 11:05:16 |
Title: fix it so it brakes, ryca Post by Matchless G11 on 06/29/19 at 11:05:16 Does any one know the cross reference for the brake pads that ryca sells for it brake upgrade? I would like to get some softer pads. The brake feels like to one that I had on my Guzzi 850t , just like a block of wood against the rotor. |
Title: Re: fix it so it brakes, ryca Post by verslagen1 on 06/29/19 at 19:27:50 find out the p/n for the caliper then find out what uses it. I think the bikebandit site can do that. |
Title: Re: fix it so it brakes, ryca Post by Ruttly on 06/29/19 at 20:34:54 I believe they are the same as the pads as 1980 Yamaha SR 500 Very available in several compounds for many suppliers But double check that before you buy them |
Title: Re: fix it so it brakes, ryca Post by Ruttly on 06/30/19 at 01:05:28 RycaShawn would know , he builds the kits. |
Title: Re: fix it so it brakes, ryca Post by Matchless G11 on 06/30/19 at 06:56:32 7A70747E757C78712F292D1D0 wrote:
The bike already has the bbk from the previous owner, I just don't know what pads go into it. |
Title: Re: fix it so it brakes, ryca Post by Gary_in_NJ on 06/30/19 at 08:03:00 If it’s the same BBK I have, then the caliper is from a first generation Yamaha R1. Is this the BBK with the 320mm rotor? |
Title: Re: fix it so it brakes, ryca Post by Matchless G11 on 06/30/19 at 15:08:47 yea it is a 320 mm |
Title: Re: fix it so it brakes, ryca Post by Matchless G11 on 06/30/19 at 15:13:18 6F7678782E2E6D7A6B7A7C742C2B2A1F0 wrote:
I am looking a SR400 myself, The ryca is a bit too café for me.[/quote] The sad thing is most all the sr500 I seen have been café or bobered out (badly) :( |
Title: Re: fix it so it brakes, ryca Post by Gary_in_NJ on 06/30/19 at 16:30:42 2C353B3B6D6D2E3928393F376F68695C0 wrote:
2004-2005 YZF-R1 rotor, caliper and pads. |
Title: Re: fix it so it brakes, ryca Post by Dave on 06/30/19 at 18:40:05 We may be talking apples/oranges a bit here. MatchlessG11 has the early 2 piece (inner/outer) brake.....and I believe that Gary_from_NJ may have that style as well. Later kits used a 1 piece Rotor that Shawn had specially made and it is not from any bike....but it uses the same caliper as the earlier kits. I have had good luck with the EBC organic brake bads on the 2 piece rotors, I have not yet found a pad that I like on the 1 piece rotors. The EBC organics squeal at slow speeds on the 1 piece rotors and don't seem to brake as strongly. If I apply the brakes and get the rotor warm the squeal goes away - but as soon as it cools the squeal comes back. I just got a set of Galfer Semi Metallic (G1054) pads to try on the 1 piece rotor, and I will give you a report in the next couple weeks after I get some miles on them. |
Title: Re: fix it so it brakes, ryca Post by Gary_in_NJ on 06/30/19 at 18:53:56 I do have the floating two piece (S40 inner / R1 outer). I looked at Matchless’ photo to be sure he has the same caliper that I do. His bracket and caliper do appear to be the same. |
SuzukiSavage.com » Powered by YaBB 2.2! YaBB © 2000-2007. All Rights Reserved. |