SuzukiSavage.com
/cgi-bin/YaBB.pl General Category >> Rubber Side Down! >> tappet question /cgi-bin/YaBB.pl?num=1451327787 Message started by rijopiatt on 12/28/15 at 10:36:27 |
Title: tappet question Post by rijopiatt on 12/28/15 at 10:36:27 I've been reading all the oil threads and my understanding is that the oil recommendations are based on the s40's use of "flat tappets". Having never opened up an engine before, my question is this: Is this referring to the pads on the lobes of the rocker arms- since when I check/adjust the valves, the screw I'm turning is referred to in some text as the "tappet adjusting screw"? BTW- based on the forum I'm switching over to the Rotella oil. |
Title: Re: tappet question Post by Serowbot on 12/28/15 at 11:32:46 574C4F4A554C445151250 wrote:
Yup... 8-) |
Title: Re: tappet question Post by Kris01 on 12/28/15 at 18:58:48 372C2F2A352C243131450 wrote:
Another convert! Good job. Your bike will love you for it. ;) |
Title: Re: tappet question Post by justin_o_guy2 on 12/28/15 at 21:52:01 Wait! Don't DO that! It's not expensive enough to be good! |
Title: Re: tappet question Post by Art Webb on 12/29/15 at 09:54:07 just remember, always wrap it before you tappet :P |
Title: Re: tappet question Post by Kris01 on 12/29/15 at 16:53:38 This thread just went WAAAAY off topic! ;D |
Title: Re: tappet question Post by Art Webb on 12/30/15 at 07:57:42 It was so easy I couldn't resist, sorry ;D |
Title: Re: tappet question Post by justin_o_guy2 on 12/30/15 at 10:00:43 I thought it was very nicely done. |
Title: Re: tappet question Post by Badger on 12/30/15 at 21:33:04 Yeah, like the way you slipped it in there. |
Title: Re: tappet question Post by Art Webb on 12/31/15 at 07:40:31 Thanks Gents |
Title: Re: tappet question Post by Kris01 on 12/31/15 at 11:31:46 123134373522500 wrote:
I'm not touching that one either! ;D |
Title: Re: tappet question Post by justin_o_guy2 on 12/31/15 at 16:54:46 Please, excuse me for pointing this out, but I think you just did. Though I thought that it too, was , for lack of a better way to say it, well placed. |
Title: Re: tappet question Post by cheapnewb24 on 12/31/15 at 17:46:20 My family's old Subaru (1990) has flat rocker arms. Believe me, I had to replace one when it broke :-/, but that's another story. I'm using Rotella T6 in it, and it seems to like it somewhat. Of course, it needed an oil change. The thing has always had trouble with noisy lifters, perhaps even when it was young. I have been wondering if that engine doesn't need some ZDDP, especially to protect against the intermittently clacking hydraulic lifters. If only I didn't have to worry about that darned cat! |
Title: Re: tappet question Post by cheapnewb24 on 12/31/15 at 17:49:48 56454340525555370 wrote:
I don't quite get it. :-? |
Title: Re: tappet question Post by cheapnewb24 on 12/31/15 at 17:54:51 I have a guess. :-? ;D |
Title: Re: tappet question Post by Art Webb on 01/01/16 at 08:54:31 78737E7A6B757E6C79292F1B0 wrote:
you're likely right, if your mind is far enough in the gutter it's a word play |
Title: Re: tappet question Post by Kris01 on 01/01/16 at 12:41:37 Art, I was going to comment on the stroke length on another thread but decided against it! :D http://suzukisavage.com/cgi-bin/YaBB.pl?num=1451621021/0#5 |
Title: Re: tappet question Post by Art Webb on 01/02/16 at 08:58:22 ;D ;D ;D |
SuzukiSavage.com » Powered by YaBB 2.2! YaBB © 2000-2007. All Rights Reserved. |