SuzukiSavage.com
/cgi-bin/YaBB.pl General Category >> Rubber Side Down! >> Anyone use a Harley Street Bob Muffler? /cgi-bin/YaBB.pl?num=1380374172 Message started by Fishbulb on 09/28/13 at 06:16:12 |
Title: Anyone use a Harley Street Bob Muffler? Post by Fishbulb on 09/28/13 at 06:16:12 I recently got a stock muffler of of my brothers retired Street Bob, part # 64895-09. For the most part it looks similar to what everyone is using, but it does not taper at the end like all the pics I have seen here. It does have the 'rail mount' and looking in the back of it, it is not straight through, it does have some baffling. I am sure I will find out once the riding season is over and I tear into it, but I was wondering if anyone had exp. with one of these. Also, I have been reading up on jetting combos, but if anyone wants to chime in with a recommendation here for this muffler, a K&N panel filter in the stock box at about sea level I am all ears! Thank you, Jac |
Title: Re: Anyone use a Harley Street Bob Muffler? Post by Fishbulb on 09/28/13 at 06:17:30 More pics |
Title: Re: Anyone use a Harley Street Bob Muffler? Post by Fishbulb on 09/28/13 at 06:18:08 Pic 3 |
Title: Re: Anyone use a Harley Street Bob Muffler? Post by Fishbulb on 09/28/13 at 06:18:34 Pic 4 |
Title: Re: Anyone use a Harley Street Bob Muffler? Post by Serowbot on 09/28/13 at 09:24:08 Can't see the rail... I assume it's there... It looks like it should mount up... (you can mount up anything with enough fiddlin')... just do it... I'd start with a #152.5 main... (do the 2/3 spacer mod, if you like... not critical)... then see how it runs... If you need to turn out the idle mix more than 3 turns,... step up one on the pilot... Making one jet change at a time,.. let's you observe the results better... Replace the float bowl screws with allen heads, and you can change jets with the carb on the bike in 5 minutes... Read my muffler guide in the Tech section for tips on install... Read my tuning guide for info on jetting... Good luck... ;)... |
Title: Re: Anyone use a Harley Street Bob Muffler? Post by justin_o_guy2 on 09/28/13 at 09:24:24 Thats nice lookin, What engine was it meant for? IF its meant to be ONe of 2 on a 1300 CC engine, then its meant for a 650 CC jugs exhaust, Sea Level ( I SOO hop[e I dont get this Bakkerds!), Lots of air in a cylinder charge, engine tends to be lean. High altitudes, its rich, with the same jetting) So, IF you let it breathe better with this exhaust, & the stock one ISrestrictive,,and IF youre close to lean already ( some models werent jetted so lean) then yea,, problee gonna wanna tinker in the carb some, |
Title: Re: Anyone use a Harley Street Bob Muffler? Post by Fishbulb on 09/30/13 at 04:03:01 Thanks guys! I am pretty sure that I run a little lean in the stock congif, so I know at least one step up in in order. Serowbot, your carb tuning page has been up in my browser for a few weeks. I keep reading it, I think some of it will 'click' once I actually tear into the job. Love the idea on the Allen Heads for the fuel bowl, do you have specs on what I am looking for at the store? I try to have have as much on hand BEFORE I tear things apart as possible! Jac |
SuzukiSavage.com » Powered by YaBB 2.2! YaBB © 2000-2007. All Rights Reserved. |