SuzukiSavage.com
/cgi-bin/YaBB.pl General Category >> Rubber Side Down! >> Re: Help me install a headlamp trim ring please!! /cgi-bin/YaBB.pl?num=1311185408 Message started by rycoman on 07/20/11 at 11:11:49 |
Title: Re: Help me install a headlamp trim ring please!! Post by rycoman on 07/20/11 at 11:11:49 I cannot seem to remove the headlamp trim ring from my suzuki s40. I have removed all the other screws except one that is connected to some wiring. Please help me out on how I can get this trim ring off. I'm new to this forum, just joined after having crashed my 05 s40. There are a few things I should be able to replace at home, but I can't seem to do it. I'm new to motorcycles and would appreciate all the help I can get on here. |
Title: Re: Help me install a headlamp trim ring please!! Post by Serowbot on 07/20/11 at 11:23:48 It has a twist lock at the top edge... Turn it about an inch... ;)... EDIT... did you remove the two screws at the bottom backside of the headlight bucket?... |
Title: Re: Help me install a headlamp trim ring please!! Post by verslagen1 on 07/20/11 at 11:27:06 not sure what you're asking, but instructions can be found in clymer's. you can find a copy in the link provided in the tech section (link below) |
Title: Re: Help me install a headlamp trim ring please!! Post by dasch on 07/20/11 at 11:39:32 below what? ;) |
Title: Re: Help me install a headlamp trim ring please!! Post by verslagen1 on 07/20/11 at 11:40:56 yes, that's it ;D |
Title: Re: Help me install a headlamp trim ring please!! Post by CalisOsin on 07/20/11 at 11:53:52 I remember the first time I pulled mine off it was stuck tight! I had all the bolts removed and it still felt like I was missing one, I just had to pull it off like it's supposed to come off and wait for it to break free. Just be gentle. |
Title: Re: Help me install a headlamp trim ring please!! Post by rycoman on 07/20/11 at 14:03:10 hey guys, i'm all over the place here i'm new to the forum and to motorcycles. I circled the part that i cannot get undone. And I do not understand what a "twist lock" is. I really appreciate everyone's help still <a href="http://www.flickr.com/photos/65437186@N02/5959162260/" title="DSC00243edithighlighted by rycoman, on Flickr"><img src="http://farm7.static.flickr.com/6124/5959162260_9dc9bf8e4e.jpg" width="500" height="375" alt="DSC00243edithighlighted"></a> |
Title: Re: Help me install a headlamp trim ring please!! Post by rycoman on 07/20/11 at 14:03:31 (click the first link) |
Title: Re: Help me install a headlamp trim ring please!! Post by Serowbot on 07/20/11 at 14:09:23 Gottcha'... Remove the screw and washer,... and there is a metal sleeve in the hole... remove that too... Then it will come out... |
Title: Re: Help me install a headlamp trim ring please!! Post by verslagen1 on 07/20/11 at 14:13:05 All factory installed fasteners use locktite about the equivalent of 'red' impact driver and proper support are recommended normally alt. method is to grab the head w/a pair of vise grips and pray. |
SuzukiSavage.com » Powered by YaBB 2.2! YaBB © 2000-2007. All Rights Reserved. |