SuzukiSavage.com
/cgi-bin/YaBB.pl General Category >> Rubber Side Down! >> header wrap? /cgi-bin/YaBB.pl?num=1298311776 Message started by weracerc on 02/21/11 at 10:09:36 |
Title: header wrap? Post by weracerc on 02/21/11 at 10:09:36 I am looking at doing my header since it is already blue and ugly the DEI wrap says to coat the finished wrap with HT silicon coating - some others do not call for this - who has done a wrap and done the coating or not ...basically is it "required" or optional to spray the HT silicone coating on it after yuo get finished wrapping it? |
Title: Re: header wrap? Post by RidgeRunner13 on 02/21/11 at 10:39:47 I used the DEI products on mine, including the paint. I used header wrap before on my racecar without the coating. The coating seals the wrap, extends the life, & IMO, just looks better. I'd recommend the paint if your going to wrap it up. 8-) BTW, mine was rusty as......living on an island in the Gulf has it's downside. >:( http://i110.photobucket.com/albums/n94/Pappygt13/Picture054.jpg http://i110.photobucket.com/albums/n94/Pappygt13/Picture052.jpg |
Title: Re: header wrap? Post by MotoBuddha on 02/21/11 at 10:50:45 I wonder if the coating keeps black wrap from turning gray. |
Title: Re: header wrap? Post by weracerc on 02/21/11 at 11:48:55 I beleive somehwere i saw that addressed that it "could" possibly keep it from fading - I got the copper colored wrap and I guess i will coat it - said to wait until the wrap dried if using the water soak application method - I applied it yesterday - drove it long enough to get it good and hot - evap the moisture and rode it to work today - suppose I will get the spray and apply it tonight after the header cools off......just a few lite coats? anyone who has done it let me know. did a little more digging - the material i used is the Titanium LR technology material - DEI says no HT coating needed. |
Title: Re: header wrap? Post by spacepirates on 02/21/11 at 13:01:26 I just got 15' of 2" DEI black header wrap off amazon for somewhere around $15. I soaked the wrap for a few minutes before putting it on and it faded pretty significantly just from that. Hasn't faded visibly after running it yet (only have about 150 miles since i put the wrap on). I opted to avoid the coating. I saw it as little more than high temp spray paint for $10, but I could be wrong. Also factoring in was me being lazy, not having a place to paint, and it being freezing outside. Stuff is cheap enough I'll risk it. If it looks terrible a year later I'll revisit the coating thing. |
Title: Re: header wrap? Post by weracerc on 02/21/11 at 13:38:29 yep i got 15' and it covered the header from the engine port to the union with the muffler. read somewhere that folks used 25' must have a healthy overlap - i tried to keep it at 1/4" overlap as recommended. |
Title: Re: header wrap? Post by sbaugz on 02/21/11 at 18:33:19 I used the DEI stuff on mine as well. Made the mistake of ordering 15 feet of the 1" stuff and it was not enough. Re-ordered 15 feet of the 2" and its the perfect length. I overlap about 1/2" on mine and use stainless steel tubing clamps to secure. I found that the stainless steel ties that it comes with don't work for crap. I used the titanium wrap, which does not require the spray, nor does it require wetting when applying. The titanium stuff lasts longer and I think the color looks cooler. |
SuzukiSavage.com » Powered by YaBB 2.2! YaBB © 2000-2007. All Rights Reserved. |