SuzukiSavage.com
/cgi-bin/YaBB.pl General Category >> Rubber Side Down! >> Engraving (?) /cgi-bin/YaBB.pl?num=1282255638 Message started by JohnBoy on 08/19/10 at 15:07:18 |
Title: Engraving (?) Post by JohnBoy on 08/19/10 at 15:07:18 http://lh4.ggpht.com/_TCSH6bqjHEM/TG2mYdMZ5KI/AAAAAAAAA0U/7WFmT6H8Cx4/s640/header% What do you think of engraving the header covers? This was my first attempt at engraving anything. Actually it was more like skrimshaw. I used a little micro jack hammer that was designed for removing very small fossles from the rock matrix in which they were found. I am not sure if I will put them back on, so I had little to lose. If it works this well on chrome it ought to be a snap cutting aluminium. By the way the headers don't have enough iron to hold my kitchen magnet, so I don't think rust will be a problem. |
Title: Re: Engraving (?) Post by babyhog on 08/19/10 at 15:36:24 I don't see a pic.... is it just me? |
Title: Re: Engraving (?) Post by Jive on 08/19/10 at 16:14:54 I see it. Very nice!! Jive |
Title: Re: Engraving (?) Post by verslagen1 on 08/19/10 at 17:19:15 nice work, i think you've found a side line. |
Title: Re: Engraving (?) Post by Skid Mark on 08/19/10 at 17:41:15 Looks good |
Title: Re: Engraving (?) Post by Serowbot on 08/19/10 at 18:19:59 Cool!... ;)... |
Title: Re: Engraving (?) Post by kimchris1 on 08/19/10 at 19:33:05 I am like Piglet, can't see any kind of a pic.. Is this some kind of joke on us gals? ;) |
Title: Re: Engraving (?) Post by Fuschia on 08/19/10 at 20:11:24 Nope.I see it. Very nice! :) |
Title: Re: Engraving (?) Post by Hashbrown on 08/19/10 at 22:35:30 you should have the other side say "thumper" |
Title: Re: Engraving (?) Post by Wake51 on 08/20/10 at 01:25:54 Now people don't have to ask... YES that's a 652 CC single cylinder... ;) |
Title: Re: Engraving (?) Post by Toymaker on 08/20/10 at 02:47:21 I don't see it. :( |
Title: Re: Engraving (?) Post by babyhog on 08/20/10 at 05:59:41 002522240825334A0 wrote:
I took the percent sign off the end of your link and I can see it now. :-? How long did it take you to do that? Looks time consuming, but I like it! http://lh4.ggpht.com/_TCSH6bqjHEM/TG2mYdMZ5KI/AAAAAAAAA0U/7WFmT6H8Cx4/s640/header |
Title: Re: Engraving (?) Post by kimchris1 on 08/20/10 at 06:19:47 Thanks Piglet for fixing the link so the rest of us can view it. JohnBoy, Ohhh wow.. That is very nice. I am in agreement with the others that believe you may have found a sideline.. Great job. :) [smiley=thumbsup.gif] [smiley=thumbsup.gif] |
Title: Re: Engraving (?) Post by Savage_Amusement on 08/20/10 at 06:32:11 I like it, would also be cool with black rubbed into the back ground to make it stand out a little bit more. I would have put 652 myself but again mad props! |
SuzukiSavage.com » Powered by YaBB 2.2! YaBB © 2000-2007. All Rights Reserved. |