SuzukiSavage.com
/cgi-bin/YaBB.pl General Category >> Rubber Side Down! >> Rear stand to remove the wheel? /cgi-bin/YaBB.pl?num=1254265828 Message started by supernes550 on 09/29/09 at 16:10:28 |
Title: Rear stand to remove the wheel? Post by supernes550 on 09/29/09 at 16:10:28 What do you guys use to prop up the rear to remove the wheel? I tried to do a search but didn't come up with anything. I have a sportbike rear stand but it doesn't look like it'll work. As you can tell this is my first cruiser. Any info is appreciated. |
Title: Re: Rear stand to remove the wheel? Post by voldigicam on 09/29/09 at 16:18:20 I rock the bike back and forth, wedging wood underneath each side alternately. Depending on where I put the wood, I can lift front or rear. |
Title: Re: Rear stand to remove the wheel? Post by justin_o_guy2 on 09/29/09 at 16:18:46 You can lay a big bloc next to the bike & lean the bike over hard to the left & kick the block under the swing arm, stand the bike up & the tire is off the ground. Either stuff another block under the left side or tie the bike so it stays up on the block. A come along in a tree works. or a rafter in the garage. Or, there is a Lift made from 2X6's , pics online Floorjack under the bracket under the bike Lumberjack holding it up while you do the work? |
Title: Re: Rear stand to remove the wheel? Post by Midnightrider on 09/29/09 at 16:36:50 Youre right a sportbike rear stand will not work unless you remove the muffler. |
Title: Re: Rear stand to remove the wheel? Post by kk lewi on 09/29/09 at 17:20:36 56494F4855526353635B49450E3C0 wrote:
http://www.nightrider.com/biketech/bikelift.htm Yup, what I built. 'Cept I used 2 2x6 screwed/glued together. Screwed a 2x4 to the top and added an eye bolt to each end for tie-downs from the bike. Stapled some carpet on one side of the 2x4 so it's smooooth lifting. It works great! I think I'll do the same thing except use 2 2x8 for my next one. Then I will be able to lift the whole bike using both. :) |
Title: Re: Rear stand to remove the wheel? Post by bill67 on 09/29/09 at 17:26:33 I make one to, I used 2 2x10s rip them down to 8 inches works real good. |
Title: Re: Rear stand to remove the wheel? Post by Paladin. on 09/29/09 at 20:54:52 I use the poor man's bike lift: http://suzukisavage.com/cgi-bin/YaBB.pl?board=tech;action=display;num=1167152229 http://i21.photobucket.com/albums/b277/gmdinusa/GMDBikeStand_1416.jpg http://paladin.savageriders.com/BikeLift.jpg |
Title: Re: Rear stand to remove the wheel? Post by supernes550 on 09/29/09 at 21:31:51 Thanks for all the info guys! Home Depot here I come. |
Title: Re: Rear stand to remove the wheel? Post by justin_o_guy2 on 09/29/09 at 22:05:39 Paladin, that looks a lot like my floorjack( orange_. Mine didnt have a cotter pin holding the pedestal into the jack. You might want to look at that. |
Title: Re: Rear stand to remove the wheel? Post by ALfromN.H. on 09/30/09 at 03:05:06 never mind going to home depot. Use a small local lumber yard/hardware store.The prices are usually less than HD and they have people that actually know what they are talking about. Support the local guy. AL |
Title: Re: Rear stand to remove the wheel? Post by Skid Mark on 09/30/09 at 09:18:27 Thanks for the pics guys. I'll be doing some winter work. Pallidin's & Justin's lifts will work great. Have the floor jack, tie downs & spare wood to do it. The pics are worth a 1,000,000 words.!!!! |
SuzukiSavage.com » Powered by YaBB 2.2! YaBB © 2000-2007. All Rights Reserved. |