SuzukiSavage.com
/cgi-bin/YaBB.pl General Category >> Rubber Side Down! >> Replacement Carb Screws /cgi-bin/YaBB.pl?num=1220036432 Message started by Mattdw on 08/29/08 at 12:00:32 |
Title: Replacement Carb Screws Post by Mattdw on 08/29/08 at 12:00:32 Where can I get some stainless hex, or 'normal' philips/flat head screws to replace top and bottom? I looked at Home Depot and Lowes. Did I look in the wrong spots? |
Title: Re: Replacement Carb Screws Post by verslagen1 on 08/29/08 at 12:06:01 Home Depot has it, hardware aile, in drawers. Ace Hardware also has a good selection and somebody to open the drawer for you. Recommend allen socket head screws. |
Title: Re: Replacement Carb Screws Post by shadowman on 08/29/08 at 13:22:59 Some Home Depots only sell limited varieties of that stuff and pre-bagged at that. Sears has these Paint/Hardware stores that sell the allen bolts, etc., individually. I just opened my carb a couple of weeks ago and really butcered the tops of the screws, of course, and want to replace them. Does anyone know the exact size?? I have been putting off removing a screw and making the trip via truck. |
Title: Re: Replacement Carb Screws Post by Digger on 08/29/08 at 19:28:57 Shadow, I don't know the size offhand, but you can prevent such predicaments in the future by getting a metric thread gauge. I'll bet one of those gauges is cheaper than the gas you'll use getting that part in your truck. Give a man a fish....... ;) |
Title: Re: Replacement Carb Screws Post by Jay on 08/29/08 at 23:48:54 ACE is the place; and for the little screws inside the carb, try a hobby shop that sells RC boats, cars, and aircraft. |
Title: Re: Replacement Carb Screws Post by Big Luke on 08/30/08 at 22:31:47 I just replaced all 8 bolts -top and bottom. They are all 5M x .80 Pitch. I believe the top ones are 8mm long and the bottom ones are 12mm long. I took one of each in so I would get the closest match. I bought 4 5M lock washers for the bottom bolts because the originals had them. Everthing was stainless steel. I got them all at this "Super" Ace about four miles from me. I call it "Super" because it is huge! I went to another Ace that was closer and smaller but they didn't have any stainless steel, metric, allen head bolts. >:( The allen head bolts look 20x better and are a lot easier to take on and off. It was well worth it. I have been tuning my carburetor and it was so much easier. Now all I need to do is remove the air box, move the the battery farther to the rear, and fabricate a mount to keep the carb from jiggling too much. Once all that is done the carb will be easy as pie to get in and out and I won't need to remove the seat or nothing. Once I get to above mentioned mod, I will post pics but until then you all can dream about it. I will also get pics of the allen head bolts shortly. Ride Hard! :) |
Title: Re: Replacement Carb Screws Post by shadowman on 08/31/08 at 04:03:22 Thanks for the fish. |
Title: Re: Replacement Carb Screws Post by Rockin_John on 08/31/08 at 09:28:31 70636163706B656C636C020 wrote:
I love that movie! ("Hitchhiker's Guide to the Galaxy"). |
Title: Re: Replacement Carb Screws Post by youzguyz on 08/31/08 at 14:37:25 The books are a lot better than either movie. (my opinion.. the books are better than the original radio shows as well) "Looks like a fish, moves like a fish, steers like a cow" |
SuzukiSavage.com » Powered by YaBB 2.2! YaBB © 2000-2007. All Rights Reserved. |