SuzukiSavage.com
/cgi-bin/YaBB.pl General Category >> Rubber Side Down! >> tank cushion. /cgi-bin/YaBB.pl?num=1156721158 Message started by Brewbrother on 08/27/06 at 16:25:58 |
Title: tank cushion. Post by Brewbrother on 08/27/06 at 16:25:58 Does anyone know the inside diameter of the tank cushion?? If not, if anyone is getting ready to do a carb mod would you slip off the custion and measure either the ID of the cushion or the OD of the cushion mount?? I'm also curious as to where I could locate a wiring diagram. I seem to have some time on my hands and my mental wheels are turning. ::) |
Title: Re: tank cushion. Post by SavageDude on 08/27/06 at 16:30:56 What type of wiring diagram do you need? I have Clymer manual for 86-03. I'll be glad to scan them and email to you. Don't know about the cushion measurement :-/ SavageDude |
Title: Re: tank cushion. Post by Keith_B on 08/27/06 at 16:31:34 :-[ I don't even know what a tank cushion is :'( |
Title: Re: tank cushion. Post by SavageDude on 08/27/06 at 16:33:31 I think he meant the rubber pieces that goes between the tank and the bike frame. |
Title: Re: tank cushion. Post by steelwolf on 08/27/06 at 16:35:23 The wiring diagram is in the back of the Clymer manual seperated by year. By the tank cushion, you mean the little rubber pieces on the frame right? |
Title: Re: tank cushion. Post by Brewbrother on 08/27/06 at 16:47:53 SavageDude wrote:
Im specifically intrested in the wiring for the tank speedo, neural and blinkers. Send them to fulf62@hotmail.com. TIA. |
Title: Re: tank cushion. Post by Brewbrother on 08/27/06 at 16:53:51 Keith_B wrote:
Its the two round rubber mount that fit into the slide channels on the tank. They are the ones that many lube to facilitate easy tank removal and installation. |
Title: Re: tank cushion. Post by Brewbrother on 08/27/06 at 16:55:14 steelwolf wrote:
Yes sir, You are correct. |
Title: Re: tank cushion. Post by azjay on 08/30/06 at 06:43:23 i replaced the tank cushions a few months ago, and i've got the old pair from debby's bike laying around the garage, i'll measure them and get back to you. |
Title: Re: tank cushion. Post by Reelthing on 08/30/06 at 19:45:02 this tech post has the diagrams - they're uploaded bigger than it shows so if you past the url in the address bar you can expand them. http://suzukisavage.com/cgi-bin/YaBB.pl?board=tech;action=display;num=1099317926 http://suzukisavage.com/images/uploaded/harnessweb.jpg http://suzukisavage.com/images/uploaded/SavElectweb.jpg |
Title: Re: tank cushion. Post by Tim_C on 08/31/06 at 08:50:03 Cushions have an O.D. of1 5/16, an I.D. of 5/16 and are 1/2" wide...hope that helps |
Title: Re: tank cushion. Post by Brewbrother on 08/31/06 at 14:58:22 Tim_C wrote:
thanks Tim C thats just what I wanted to know. |
Title: Re: tank cushion. Post by Brewbrother on 08/31/06 at 15:00:58 Reelthing wrote:
Thanks much for those diagrams. They were quite nice and very helpful. The gears are really turning now. |
SuzukiSavage.com » Powered by YaBB 2.2! YaBB © 2000-2007. All Rights Reserved. |